Black Box LC-XE10 instruction manual Lamp Handling Precautions, Lamp Replace Counter

Page 46

Maintenance and Cleaning

Lamp Replace Counter

Be sure to reset the lamp replace counter after the lamp is replaced. When the lamp replace counter is reset, the LAMP REPLACE indicator stops lighting.

1

Turn the projector on, press the MENU button and the On-

 

Screen Menu will appear. Press the Point Left/Right button

 

to move the red frame pointer to the Setting Menu icon.

2

Press the Point Down button to move the red frame pointer

to the Lamp counter reset item and then press the SELECT

 

button. The message "Lamp replace counter Reset?" is

 

displayed. Move the pointer to [Yes] and then press the

 

SELECT button.

3

Another confirmation dialog box appears and select [Yes] to

 

reset the Lamp replace counter.

NOTE

●Do not reset the Lamp replace counter without implementation of lamp replacement. Be sure to reset the Lamp replace counter only after replacing the lamp.

Move the pointer to Lamp counter reset and then press the SELECT button. The message “Lamp replace counter Reset?” is displayed.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

●Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

●If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

( Follow carefully the instructions in the Lamp Replacement section of this manual. ) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

●A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Model LC-XE10 Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandAir Circulation Safety InstructionsInstalling the Projector in Proper Position Moving the ProjectorCompliance Federal Communication Commission NoticeFor the U.S.A. and Canada ComplianceFor Continental Europe 200 240 V ACFeatures and Design Part Names and Functions Front Back BottomPart Names and Functions TerminalTop 1!2Remote Control Zoom FreezeLaser Pointer Function Pointer FunctionRemote Control Code Wireless Mouse OperationRemote Control Operating Range Remote Control Batteries InstallationAdjustable Feet InstallationPositioning the Projector Connecting to a Computer InstallationTerminals Projector Connecting to Video Equipment Video Source exampleTurning On the Projector Basic OperationTurning Off the Projector Keystone Adjustment Zoom AdjustmentFocus Adjustment Basic OperationPicture Freeze Function Auto Set Up FunctionKeystone correction Corner No Show Function Timer FunctionSound Adjustment Direct OperationTop Control Remote ControlOn-Screen Menu On-Screen MenuMenu Bar Computer Input Input Source SelectionAuto Computer InputComputer System Selection ModeTo store adjustment data Computer Adjustment AutoAuto PC Adj Computer Adjustment Manual Display area To store adjustment data ResetMode free To clear adjustment dataReal Image Level SelectionStandard Image button Standard RealImage Level Adjustment Screen Size Adjustment Input Source Selection Video, S-Video, Y, Pb/Cb, Pr/Cr Video InputPb/Cb, Pr/Cr RGB Scart Video InputInput Source Selection RGB Scart 21-Pin Input button Computer Video Computer 2 buttonComponent Video System SelectionVideo or S-Video AV System Menu Video or S-VideoCinema Image button Standard CinemaTint ColorProgressive Resets all adjustment to their previous figure Setting SettingSetting On start Power managementLamp mode PointerProjector mode To change the code for the remote controlWireless Mouse mode To change the code for the projectorProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the items below Cleaning the Projection Lens Maintenance and CleaningCleaning the Air Filters Cleaning the Projector CabinetLamp Replacement Reset the Lamp replace counterLamp Handling Precautions Lamp Replace CounterTroubleshooting AppendixAppendix Indicators and Projector Condition Projector ConditionMenu Tree PC AdjustImage Adjust Screen InputImage Select System SettingImage Adjust SoundFreq Compatible Computer SpecificationsKHz Technical Specifications Terminal HDB15-PIN Pin Configuration Configurations of TerminalsTerminal DVI-I Pin Configuration Optional Parts Attaching the Lens Cover To lock the projector with USB key Key registrationDeleting key registration Off Projector is not locked with USB Key On1Appendix Appendix Key to better communications Canada
Top Page Image Contents