Black Box LC-XE10 instruction manual Power management, On start, Lamp mode, Pointer

Page 41

Setting

Power management

For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the input signal is interrupted and no button is pressed for 30 seconds or more.

When the input signal is interrupted and no button is pressed for 30 seconds or more, the timer display with the message "No signal" appears on the screen. The count-down starts for the time to have been set. The count-down time can be set between 1 and 30 minutes.

When the count-down time has elapsed, the lamp will be turned off to cool itself down. The POWER indicator is flashing red during this cooling-off period. The next performance depends on setting as follows.

Ready ······ When the lamp has been fully cooled down, the POWER indicator changes to green flashing. In this condition, the projection lamp will be turned on if the input signal is reconnected or any button on the top control or remote control is pressed.

Shutdown···· When the lamp has been fully cooled down, the power will be turned off.

Off ···············The Power management function is canceled.

On start

When this function is “On,” the projector is automatically turned on just by connecting the AC power cord to a wall outlet.

Power management

Time left until Lamp

off

Press the SELECT button at Power management and this box appears. Choose one of three settings with the Point Left/Right button, and go to the timer with the Point Up/Down button and set time with the Point Left/Right button.

NOTE

●Be sure to turn the projector off properly (see “Turning Off the Projector” on page 19). If the projector is turned off in the wrong steps, the On start function does not operate properly.

Lamp mode

This function allows you to change brightness of the screen.

···· normal brightness

···· the controlled brightness according with input signal

···· lowers brightness and reduces the lamp power

consumption.

Pointer

Pointer

You can emphasize a part of the projected image with this function. Choose either Spotlight or Pointer with the Point Up/Down button and press the SELECT button. Then select one of three different sizes (Large, Middle, and Small) of Spotlight or a pointer of three different patterns (Arrow, Finger, and Dot) of Pointer. (See page 13 for operation.)

Select Spotlight or Pointer with the Point Up/Down button and press the SELECT button. Then select size or pattern with the Point Left/Right button.

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Model LC-XE10 Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsInstalling the Projector in Proper Position Safety InstructionsAir Circulation Moving the ProjectorFederal Communication Commission Notice ComplianceFor Continental Europe ComplianceFor the U.S.A. and Canada 200 240 V ACFeatures and Design Front Back Bottom Part Names and FunctionsTerminal Part Names and Functions1!2 TopZoom Freeze Remote ControlPointer Function Laser Pointer FunctionWireless Mouse Operation Remote Control CodeRemote Control Batteries Installation Remote Control Operating RangePositioning the Projector InstallationAdjustable Feet Terminals Projector InstallationConnecting to a Computer Video Source example Connecting to Video EquipmentTurning Off the Projector Basic OperationTurning On the Projector Focus Adjustment Zoom AdjustmentKeystone Adjustment Basic OperationKeystone correction Corner Auto Set Up FunctionPicture Freeze Function Sound Adjustment Timer FunctionNo Show Function Direct OperationOn-Screen Menu Remote ControlTop Control On-Screen MenuMenu Bar Input Source Selection Computer InputComputer System Selection Computer InputAuto ModeAuto PC Adj Computer Adjustment AutoTo store adjustment data Computer Adjustment Manual Mode free ResetDisplay area To store adjustment data To clear adjustment dataStandard Image Level SelectionReal Image button Standard RealImage Level Adjustment Screen Size Adjustment Pb/Cb, Pr/Cr Video InputInput Source Selection Video, S-Video, Y, Pb/Cb, Pr/Cr Input Source Selection RGB Scart 21-Pin Video InputRGB Scart Input button Computer Video Computer 2 buttonVideo or S-Video Video System SelectionComponent AV System Menu Video or S-VideoImage button Standard Cinema CinemaProgressive ColorTint Resets all adjustment to their previous figure Setting SettingSetting Lamp mode Power managementOn start PointerWireless Mouse mode To change the code for the remote controlProjector mode To change the code for the projectorThen check the items below Maintenance and CleaningProjector is shut down and the Warning indicator lights red Cleaning the Air Filters Maintenance and CleaningCleaning the Projection Lens Cleaning the Projector CabinetReset the Lamp replace counter Lamp ReplacementLamp Replace Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector Condition Indicators and Projector ConditionImage Adjust Screen PC AdjustMenu Tree InputImage Adjust System SettingImage Select SoundKHz Compatible Computer SpecificationsFreq Technical Specifications Terminal DVI-I Pin Configuration Configurations of TerminalsTerminal HDB15-PIN Pin Configuration Optional Parts Attaching the Lens Cover Deleting key registration Key registrationTo lock the projector with USB key Off Projector is not locked with USB Key On1Appendix Appendix Key to better communications Canada
Top Page Image Contents