BenQ MP723 user manual Information menu

Page 52

INFORMATION menu

This menu shows you the current operating status of the projector.

Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on the screen.

FUNCTION	DESCRIPTION

	FAQ-Image and
	Installation	Displays possible solutions to problems you may encounter.

	FAQ-Features
	FAQ-Features
	and Service

		Source
		Shows the current signal source.
		Picture mode
		Shows the selected mode in the PICTURE menu.
	Current System	Resolution
	Status	Shows the native resolution of the input signal.
		Color system
		Shows input system format, NTSC, PAL, SECAM, or RGB.
		Equivalent Lamp Hour
		Displays the number of hours the lamp has been used.

52 Operation

Image 52

Contents Welcome Table of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Allow at least 50 cm clearance from walls Bedding or any other soft surfaceResulting in damage to the projector Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior viewLamp cover Controls and functions ProjectorRemote control CaptureIndicator light 22. D. Zoom + Operating the Laser pointerReplacing the remote control batteries Remote control effective rangeApprox.15 Set Rear Ceiling in the System Setup Basic Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Maximum zoom Minimum zoom Screen Center of lens Projection distance1219 1500Connecting a computer Connecting a computer or monitorConnection Iii Connecting a monitor With a VGA cable With a VGA to DVI-A cableConnecting Video source devices Connecting AudioBest video quality Better video qualityConnecting a DVI source device Connecting a Component Video source device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceDevice Connecting a composite Video source device To connect the projector to a composite Video source deviceProjection lamp Press I I Power on the projector or remote OperationStarting up the projector OperationUsing the menus Use / to highlight the System Setup Basic menuUsing a security cable lock Utilizing the password functionSecuring the projector Removing the control keypad on the projectorSetting a password If you forget the passwordTo the Security Settings Respectively represent 4 digitsEntering the password recall procedure Changing the passwordDisabling the password function Enter a new passwordSwitching input signal Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityOn the projector or remote Control Correcting keystoneSelecting the aspect ratio About the aspect ratioUsing Wall Color Selecting a picture modePC/DVI-A/DVI-D Signal Input Optimizing the imageFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorEvery adjustment made will reflect to 3D Color ManagementSetting the presentation timer You want the timer to show up on the screen byTo cancel the timer, perform the following steps How to use the Timer ON/SHOW button?Remote paging operations Button is a multi-functional keyHiding the image Freezing the imageGo to the System Setup Basic Panel Key Lock Utilizing FAQ functionLocking control keys Setup Advanced High Altitude Mode, select On Operating in a high altitude environmentCreating your own startup screen To activate the High Altitude Mode, go to the SystemAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Personalizing the projector menu displayShutting down the projector Approximately 90 seconds to cool down the projectorMenu operation Menu systemBasic AdvancedDisplay menu Source menuPicture menu System Setup Basic menu System Setup Advanced menu Information menu Maintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampTighten the screw that secures the lamp Resetting the lamp timer Restart the projectorIndicators Troubleshooting Remote control does not workProjector does not turn on No pictureSpecifications Projector specificationsDimensions Mm W x 131.30 mm H x 304.99 mm D 274.87 48.57 SpecificationsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSignal Format Horizontal Vertical Frequency Frequency kHz Supported timing for PC including DVI-D input15.73 Specifications Supported timing for Video and S-Video inputs15.73 15.63Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive

INFORMATION menu

and Service

Status

52 Operation