BenQ MP723 user manual Indicators

Page 59

Indicators

Light

 

 

Status & Description

 

 

 

 

 

Power

Temp

Lamp

 

 

 

 

 

 

 

Power events

 

 

 

 

 

 

 

Orange

Orange

Orange

The projector has just been connected to a power outlet or the

 

 

 

lamp door is open.

Orange

Off

Off

Stand-by mode.

Green

Off

Off

Powering up.

Flashing

 

 

 

 

Green

Off

Off

Normal operation.

 

 

 

1.

The projector needs 90 seconds to cool down as it was

Orange

 

 

 

abnormally shut down without the normal cooling down

Off

Off

 

process. Or

Flashing

 

 

 

2.

The projector needs to cool for 90 seconds after the

 

 

 

 

 

 

 

power is turned off.

 

 

 

 

Orange

Off

Off

The projector has shutdown automatically. If you try to re-start

the projector, it will shutdown again. Please contact your dealer

Flashing

 

 

for assistance.

 

 

 

 

 

 

 

 

Lamp events

 

 

 

 

 

 

 

Orange

Off

Red

The projector has shutdown automatically. If you try to re-start

the projector, it will shutdown again. Please contact your dealer

Flashing

 

 

for assistance.

 

 

 

 

 

 

 

 

Off

Off

Red

1.

The projector needs 90 seconds to cool down. Or

2.

Please contact your dealer for assistance.

 

 

 

 

 

 

 

 

Thermal events

Off

Red

Off

Off

Red

Red

Off

Red

Green

Off

Red

Orange

Red

Red

Red

Red

Red

Green

Red

Red

Orange

Green

Red

Red

Green

Red

Green

Green

Red

Orange

Orange

Red

Red

Orange

Red

Green

Orange

Red

Orange

Off

Green

Red

Off

Green

Green

 

 

 

The projector has shutdown automatically. If you try to re-start the projector, it will shutdown again. Please contact your dealer for assistance.

Maintenance 59

Image 59
Contents Welcome Table of contents Do not look straight at the projector Important safety instructionsRefer servicing to qualified service personnel Future reference Projector lamp is onSafety Instructions Resulting in damage to the projector Bedding or any other soft surfaceAllow at least 50 cm clearance from walls Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Lamp cover Projector exterior viewFront/upper side Rear/lower side Projector Controls and functionsCapture Remote controlOperating the Laser pointer Indicator light 22. D. Zoom +Approx.15 Remote control effective rangeReplacing the remote control batteries Front Table Set Rear Ceiling in the System Setup BasicPositioning your projector Choosing a locationObtaining a preferred projected image size Page 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Connection Connecting a computer or monitorConnecting a computer Iii With a VGA cable With a VGA to DVI-A cable Connecting a monitorBetter video quality Connecting Video source devicesConnecting Audio Best video qualityConnecting a DVI source device To connect the projector to a Component Video source device Connecting a Component Video source deviceDevice Connecting an S-Video source deviceTo connect the projector to an S-Video source device To connect the projector to a composite Video source device Connecting a composite Video source deviceOperation Projection lamp Press I I Power on the projector or remoteOperation Starting up the projectorUse / to highlight the System Setup Basic menu Using the menusRemoving the control keypad on the projector Using a security cable lockUtilizing the password function Securing the projectorRespectively represent 4 digits Setting a passwordIf you forget the password To the Security SettingsEnter a new password Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone On the projector or remote ControlAbout the aspect ratio Selecting the aspect ratioOptimizing the image Using Wall ColorSelecting a picture mode PC/DVI-A/DVI-D Signal InputAdjusting Contrast Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting Sharpness3D Color Management Every adjustment made will reflect toYou want the timer to show up on the screen by Setting the presentation timerButton is a multi-functional key To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW button? Remote paging operationsFreezing the image Hiding the imageLocking control keys Utilizing FAQ functionGo to the System Setup Basic Panel Key Lock To activate the High Altitude Mode, go to the System Setup Advanced High Altitude Mode, select OnOperating in a high altitude environment Creating your own startup screenPersonalizing the projector menu display Adjusting the soundAdjusting the sound level Turning off the Power on/off ring toneApproximately 90 seconds to cool down the projector Shutting down the projectorMenu system Menu operationAdvanced BasicSource menu Display menuPicture menu System Setup Basic menu System Setup Advanced menu Information menu Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenanceTighten the screw that secures the lamp Restart the projector Resetting the lamp timerIndicators No picture TroubleshootingRemote control does not work Projector does not turn onProjector specifications SpecificationsMm W x 131.30 mm H x 304.99 mm D 274.87 48.57 Specifications DimensionsSupported timing for PC including DVI-D input Timing chartHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Signal Format Horizontal Vertical Frequency Frequency kHz15.63 15.73 SpecificationsSupported timing for Video and S-Video inputs 15.73Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statement