BenQ MP723 user manual Restart the projector, Resetting the lamp timer

Page 58

10.Use a coin to turn the screw clockwise until the lamp cover is secured.

•Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screw.

11.Restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

12. After the startup logo, open the On-Screen Notice Display (OSD) menu. Go to the SYSTEM

SETUP: Advanced > Lamp Settings menu. Press Mode/enter on the projector or ENTER on the remote control. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press Mode/enter on the projector or ENTER on the remote control. The lamp time will be reset to '0'.

Do not reset if the lamp is not new or replaced as this could cause damage.

Reset Lamp Timer?

Reset Cancel

58 Maintenance

Image 58

Contents Welcome Table of contents Future reference Projector lamp is on Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorSafety Instructions Allow at least 50 cm clearance from walls Bedding or any other soft surfaceResulting in damage to the projector Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior viewLamp cover Controls and functions ProjectorRemote control CaptureIndicator light 22. D. Zoom + Operating the Laser pointerReplacing the remote control batteries Remote control effective rangeApprox.15 Choosing a location Set Rear Ceiling in the System Setup BasicPositioning your projector Front TableObtaining a preferred projected image size Page 1219 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1500Connecting a computer Connecting a computer or monitorConnection Iii Connecting a monitor With a VGA cable With a VGA to DVI-A cableBest video quality Connecting Video source devicesConnecting Audio Better video qualityConnecting a DVI source device Connecting a Component Video source device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceDevice Connecting a composite Video source device To connect the projector to a composite Video source deviceStarting up the projector Projection lamp Press I I Power on the projector or remoteOperation OperationUsing the menus Use / to highlight the System Setup Basic menuSecuring the projector Using a security cable lockUtilizing the password function Removing the control keypad on the projectorTo the Security Settings Setting a passwordIf you forget the password Respectively represent 4 digitsDisabling the password function Entering the password recall procedureChanging the password Enter a new passwordSwitching input signal Changing Color SpaceAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityOn the projector or remote Control Correcting keystoneSelecting the aspect ratio About the aspect ratioPC/DVI-A/DVI-D Signal Input Using Wall ColorSelecting a picture mode Optimizing the imageAdjusting Brightness Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting ContrastAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorEvery adjustment made will reflect to 3D Color ManagementSetting the presentation timer You want the timer to show up on the screen byRemote paging operations To cancel the timer, perform the following stepsHow to use the Timer ON/SHOW button? Button is a multi-functional keyHiding the image Freezing the imageGo to the System Setup Basic Panel Key Lock Utilizing FAQ functionLocking control keys Creating your own startup screen Setup Advanced High Altitude Mode, select OnOperating in a high altitude environment To activate the High Altitude Mode, go to the SystemTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Personalizing the projector menu displayShutting down the projector Approximately 90 seconds to cool down the projectorMenu operation Menu systemBasic AdvancedDisplay menu Source menuPicture menu System Setup Basic menu System Setup Advanced menu Information menu Maintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampTighten the screw that secures the lamp Resetting the lamp timer Restart the projectorIndicators Projector does not turn on TroubleshootingRemote control does not work No pictureSpecifications Projector specificationsDimensions Mm W x 131.30 mm H x 304.99 mm D 274.87 48.57 SpecificationsSignal Format Horizontal Vertical Frequency Frequency kHz Timing chartHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Supported timing for PC including DVI-D input15.73 15.73 SpecificationsSupported timing for Video and S-Video inputs 15.63Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive