BenQ MP723 Shutting down the projector, Approximately 90 seconds to cool down the projector

Page 45

Shutting down the projector

1.Press II Power and a confirmation message will display prompting you.

If you don't respond in a few seconds, the message will disappear.

2.	Press II Power a second time. The Power
	indicator light flashes orange, the projection lamp
	shuts down, and the fans will continue to run for

approximately 90 seconds to cool down the projector.

To protect the lamp, the projector will not respond to any commands during the cooling process.

To shorten the cooling time, you can also activate the Quick cooling function. See "Quick Cooling" on page 51 for details.

3.Once the cooling process finishes, a "Power Off Ring Tone" will be heard. The Power indicator light is a steady orange and fans stop. Disconnect the power cord from the wall socket.

•To turn off the power ring tone, see "Turning off the Power on/off ring tone" on page 44 for details.

•If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press Power again to start the projector after the fans stop and the Power indicator light turns orange.

Operation 45

Image 45

Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Bedding or any other soft surface Allow at least 50 cm clearance from wallsResulting in damage to the projector Ceiling mounting the projector Projector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideLamp cover Projector Controls and functionsCapture Remote controlOperating the Laser pointer Indicator light 22. D. Zoom +Remote control effective range Replacing the remote control batteriesApprox.15 Positioning your projector Set Rear Ceiling in the System Setup BasicChoosing a location Front TableObtaining a preferred projected image size Page Screen Center of lens Projection distance Maximum zoom Minimum zoom1219 1500Connecting a computer or monitor Connecting a computerConnection Iii With a VGA cable With a VGA to DVI-A cable Connecting a monitorConnecting Audio Connecting Video source devicesBest video quality Better video qualityConnecting a DVI source device To connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceDevice To connect the projector to a composite Video source device Connecting a composite Video source deviceOperation Projection lamp Press I I Power on the projector or remoteStarting up the projector OperationUse / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSecuring the projector Removing the control keypad on the projectorIf you forget the password Setting a passwordTo the Security Settings Respectively represent 4 digitsChanging the password Entering the password recall procedureDisabling the password function Enter a new passwordChanging Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone On the projector or remote ControlAbout the aspect ratio Selecting the aspect ratioSelecting a picture mode Using Wall ColorPC/DVI-A/DVI-D Signal Input Optimizing the imageSetting the User 1/User 2 mode Fine-tuning the image quality in user modesAdjusting Brightness Adjusting ContrastAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant Color3D Color Management Every adjustment made will reflect toYou want the timer to show up on the screen by Setting the presentation timerHow to use the Timer ON/SHOW button? To cancel the timer, perform the following stepsRemote paging operations Button is a multi-functional keyFreezing the image Hiding the imageUtilizing FAQ function Go to the System Setup Basic Panel Key LockLocking control keys Operating in a high altitude environment Setup Advanced High Altitude Mode, select OnCreating your own startup screen To activate the High Altitude Mode, go to the SystemAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Personalizing the projector menu displayApproximately 90 seconds to cool down the projector Shutting down the projectorMenu system Menu operationAdvanced BasicSource menu Display menuPicture menu System Setup Basic menu System Setup Advanced menu Information menu Care of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenanceTighten the screw that secures the lamp Restart the projector Resetting the lamp timerIndicators Remote control does not work TroubleshootingProjector does not turn on No pictureProjector specifications SpecificationsMm W x 131.30 mm H x 304.99 mm D 274.87 48.57 Specifications DimensionsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Timing chartSignal Format Horizontal Vertical Frequency Frequency kHz Supported timing for PC including DVI-D inputSupported timing for Video and S-Video inputs 15.73 Specifications15.73 15.63Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive