Table of contents

BenQ MP522 ST, MP512 ST user manual Table of contents

Page 2

Table of contents
Important safety
instructions	3
Introduction	7
Projector features	7
Shipping contents	8
Projector exterior view	9
Controls and functions	10
Positioning your
projector	13
Choosing a location	13
Obtaining a preferred projected
image size	14
Connection	17
Connecting a computer or monitor...	17
Connecting Video source devices	19
Operation	24
Starting up the projector	24
Using the menus	25
Utilizing the password function	26
Switching input signal	28
Adjusting the projected image	29
Magnifying and searching for
details	30
Selecting the aspect ratio	31
Optimizing the image	32
Setting the presentation timer	36
Hiding the image	37
Locking control keys	38
Freezing the image	38
Utilizing FAQ function	38

Operating in a high altitude
environment	39
Adjusting the sound	39
Personalizing the projector
menu display	40
Shutting down the projector	40
Menu operation	41
Maintenance	49
Care of the projector	49
Lamp information	50
Troubleshooting	56
Specifications	57
Projector specifications	57
Dimensions	58
Timing chart	58
Warranty and Copyright
information	61
Regulation
statements	62

2 Table of contents

Image 2

Contents

Welcome MP512 ST/MP522 ST Digital ProjectorTable of contents Future reference Projector lamp is on Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector This Apparatus Must be EarthedIntroduction Projector featuresIntroduction Shipping contents MP522 ST Projector exterior viewFront/upper side Rear/lower side MP512 ST External control panelControls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Positioning your projector Choosing a locationObtaining a preferred projected image size Page Projection dimensions Connection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorBest video quality Connecting Video source devicesConnecting audio Better video qualityConnecting an Hdmi device To connect the projector to an Hdmi deviceComponent Video to VGA D-Sub adaptor cable Audio cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device Cable Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Audio cable Video cable Connecting a composite Video source deviceTo connect the projector to a composite Video source device Operation OperationStarting up the projector Using the menus Use / to highlight the System Setup Basic menuIf you forget the password Utilizing the password functionSetting a password Security SettingsDisabling the password function Entering the password recall procedureChanging the password Enter a new passwordChanging color space Switching input signalSignal Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioPC input signals D-Sub / Comp. analog RGB Selecting a picture modePicture modes for different types of signals Optimizing the imageSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightHiding the image To cancel the timer, perform the following stepsHow to use the Timer On key? Locking control keys Utilizing FAQ functionOr go to the System Setup Basic Panel Freezing the imageTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Basic LanguageEquivalent lamp hour System Setup AdvancedPicture Mode SecurityDescription of each menu Timer TemperatureSave Settings Auto PowerPanel Key Sleep TimerSettings LockLamp System Setup Advanced menuReset All SecurityInformation menu FAQ-Image InstallationFeatures Service CurrentMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Displays. Press to highlight Reset lamp Resetting the lamp timerSetup Advanced Lamp Settings menu Tighten the screw that secures the lampIndicators Troubleshooting Specifications Projector specificationsMm W x 90 mm H x 214 mm D 255 61.5 DimensionsRefresh rate Horizontal Clock Resolution Mode MHzVideo Hdcp Resolution ModeSupported timing for Hdmi Hdcp input-MP512 ST Signal Format Supported timing for PC input-MP522 STCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive

BenQ MP522 ST, MP512 ST user manual Table of contents