BenQ MP512 ST, MP522 ST user manual Adjusting the projected image, Adjusting the projection angle

Page 29

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1.Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2.Screw the rear adjuster foot to fine tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

1

2

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 30 for details.

•Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

•Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

•The screen will be blank while AUTO is functioning.

•This function is only available when a PC signal (analog RGB) is selected.

Fine-tuning the image clarity

Sharpen the image by rotating the focus ring.

Operation 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents
MP512 ST/MP522 ST Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Ceiling mounting the projectorIntroduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior viewMP522 ST MP512 ST External control panelProjector Controls and functionsRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size Page Projection dimensions Connecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorConnecting audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an Hdmi device Connecting an Hdmi deviceComponent Video to VGA D-Sub adaptor cable Audio cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device Cable Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Audio cable Video cable Connecting a composite Video source deviceTo connect the projector to a composite Video source device Operation OperationStarting up the projector Use / to highlight the System Setup Basic menu Using the menusSetting a password Utilizing the password functionIf you forget the password Security SettingsChanging the password Entering the password recall procedureDisabling the password function Enter a new passwordChanging color space Switching input signalSignal Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp. analog RGB Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Top-Left Bottom-Left Top- Right Bottom-Right Setting the presentation timerHiding the image To cancel the timer, perform the following stepsHow to use the Timer On key? Or go to the System Setup Basic Panel Utilizing FAQ functionLocking control keys Freezing the imageAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMain menu Sub-menu Options Menu operationMenu system Language BasicPicture Mode System Setup AdvancedEquivalent lamp hour SecurityDescription of each menu Save Settings TemperatureTimer Auto PowerSettings Sleep TimerPanel Key LockReset All System Setup Advanced menuLamp SecurityFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenancePage Setup Advanced Lamp Settings menu Resetting the lamp timerDisplays. Press to highlight Reset lamp Tighten the screw that secures the lampIndicators Troubleshooting Projector specifications SpecificationsRefresh rate Horizontal Clock Resolution Mode DimensionsMm W x 90 mm H x 214 mm D 255 61.5 MHzVideo Hdcp Resolution ModeSupported timing for Hdmi Hdcp input-MP512 ST Supported timing for PC input-MP522 ST Signal FormatLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive
Top Page Image Contents