BenQ MP522 ST Panel Key, Lock, Sleep Timer, Splash, Screen, Quick, Cooling, High Altitude, Audio

Page 46

FUNCTION (default setting/ value)

4.

Panel Key

Lock

SYSTEMSETUP: Basicmenu

(Off)

 

 

Sleep Timer

 

(Disable)

 

Splash

 

Screen

 

(BenQ logo)

 

Quick

 

Cooling

 

(On)

5.

High Altitude

SYSTEM

Mode

 

SETUP:

(Off)

Audio

 

Advancedmenu

Settings

Menu

 

 

Settings

 

Standby D-

 

Sub Output

 

(Off)

DESCRIPTION (default setting/value)

Disables or enables all panel key functions except II Power on the projector and keys on the remote control. See "Locking control keys" on page 38 for details.

Sets the auto-shutdown timer. The timer can be set to a value between 30 minutes and 12 hours.

Allows you to select which logo screen will display during projector start-up. Three options are available: BenQ logo, Black screen, or Blue screen.

Selecting On enables the function and the projector cooling time will be shortened to a few seconds.

If you attempt to restart the projector right after the quick cooling process, it may not be turned on successfully and will rerun its cooling fans.

A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 39 for details.

Mute (Off)

Volume (5)

Power on/off ring tone (On)

See "Adjusting the sound" on page 39 for details.

Menu display time (15 sec)

Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu position (Center)

Sets the On-Screen Display (OSD) menu position.

Selecting On enables the function. The projector can output a VGA signal when it is in standby mode and the D-SUB IN and D-SUB OUT sockets are correctly connected to devices. See "Connecting a monitor" on page 18 for how to make the connection.

Enabling this function slightly increases the standby power consumption.

46 Operation

Page 45 Page 47
Image 46
Page 45 Page 47
Contents
Welcome MP512 ST/MP522 ST Digital ProjectorTable of contents Future reference Projector lamp is on Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector This Apparatus Must be EarthedIntroduction Projector featuresIntroduction Shipping contents MP522 ST Projector exterior viewFront/upper side Rear/lower side MP512 ST External control panelControls and functions ProjectorRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Positioning your projector Choosing a locationObtaining a preferred projected image size Page Projection dimensions Connection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorBest video quality Connecting Video source devicesConnecting audio Better video qualityConnecting an Hdmi device To connect the projector to an Hdmi deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceComponent Video to VGA D-Sub adaptor cable Audio cable To connect the projector to an S-Video source device Connecting an S-Video source deviceCable Video cable To connect the projector to a composite Video source device Connecting a composite Video source deviceAudio cable Video cable Starting up the projector OperationOperation Using the menus Use / to highlight the System Setup Basic menuIf you forget the password Utilizing the password functionSetting a password Security SettingsDisabling the password function Entering the password recall procedureChanging the password Enter a new passwordSignal Switching input signalChanging color space Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioPC input signals D-Sub / Comp. analog RGB Selecting a picture modePicture modes for different types of signals Optimizing the imageSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightHow to use the Timer On key? To cancel the timer, perform the following stepsHiding the image Locking control keys Utilizing FAQ functionOr go to the System Setup Basic Panel Freezing the imageTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Basic LanguageEquivalent lamp hour System Setup AdvancedPicture Mode SecurityDescription of each menu Timer TemperatureSave Settings Auto PowerPanel Key Sleep TimerSettings LockLamp System Setup Advanced menuReset All SecurityInformation menu FAQ-Image InstallationFeatures Service CurrentMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Displays. Press to highlight Reset lamp Resetting the lamp timerSetup Advanced Lamp Settings menu Tighten the screw that secures the lampIndicators Troubleshooting Specifications Projector specificationsMm W x 90 mm H x 214 mm D 255 61.5 DimensionsRefresh rate Horizontal Clock Resolution Mode MHzSupported timing for Hdmi Hdcp input-MP512 ST Resolution ModeVideo Hdcp Signal Format Supported timing for PC input-MP522 STCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive
Top Page Image Contents