BenQ MP522 ST, MP512 ST user manual Description of each menu

Page 44

Description of each menu

1. DISPLAY menu

2. PICTURE menu

FUNCTION

DESCRIPTION (default setting/value)

(default setting/

value)

 

Wall Color

Corrects the projected picture’s color when the projection surface is

not white. See "Using Wall Color" on page 33 for details.

(Off)

 

 

 

Aspect Ratio

There are four options to set the image's aspect ratio depending on

(Auto)

your input signal source. See "Selecting the aspect ratio" on page 31 for

details.

 

 

Keystone

Corrects any keystoning of the image. See "Correcting keystone" on

page 30 for details.

(0)

 

 

 

Position

Displays the position adjustment page. To move the projected image,

use the directional arrow keys. The values shown on the lower position

(0)of the page change with every key press you made until they reach their maximum or minimum.

Phase

Adjusts the clock phase to reduce image

distortion.

(depends on the

 

selected input

 

signal)

 

 

 

H. Size

Adjusts the horizontal width of the image.

(0)

 

 

 

Digital Zoom

Magnifies or reduces the projected image. See "Magnifying and

searching for details" on page 30 for details.

(1.0X)

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

(PC source:

projector image set-up to suit your program type. See "Selecting a

picture mode" on page 32 for details.

Dynamic;

 

Video source:

 

Standard)

 

 

 

Reference

Selects a picture mode that most suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 33 for

(Dynamic)

details.

 

 

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on

page 33 for details.

(50)

 

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 33 for details.

(0)

 

 

 

Color

Adjusts the color saturation level -- the amount of each color in a

video image. See "Adjusting Color" on page 34 for details.

(0)

 

44 Operation

Image 44
Contents Welcome MP512 ST/MP522 ST Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector This Apparatus Must be EarthedIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideMP522 ST MP512 ST External control panelControls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Positioning your projector Choosing a locationObtaining a preferred projected image size Page Projection dimensions Connecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorConnecting Video source devices Connecting audioBest video quality Better video qualityConnecting an Hdmi device To connect the projector to an Hdmi deviceComponent Video to VGA D-Sub adaptor cable Audio cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device Cable Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Audio cable Video cable Connecting a composite Video source deviceTo connect the projector to a composite Video source device Operation OperationStarting up the projector Using the menus Use / to highlight the System Setup Basic menuUtilizing the password function Setting a passwordIf you forget the password Security SettingsEntering the password recall procedure Changing the passwordDisabling the password function Enter a new passwordChanging color space Switching input signalSignal Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioSelecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp. analog RGB Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightHiding the image To cancel the timer, perform the following stepsHow to use the Timer On key? Utilizing FAQ function Or go to the System Setup Basic PanelLocking control keys Freezing the imageAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Basic LanguageSystem Setup Advanced Picture ModeEquivalent lamp hour SecurityDescription of each menu Temperature Save SettingsTimer Auto PowerSleep Timer SettingsPanel Key LockSystem Setup Advanced menu Reset AllLamp SecurityFAQ-Image Installation Features ServiceInformation menu CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Resetting the lamp timer Setup Advanced Lamp Settings menuDisplays. Press to highlight Reset lamp Tighten the screw that secures the lampIndicators Troubleshooting Specifications Projector specificationsDimensions Refresh rate Horizontal Clock Resolution ModeMm W x 90 mm H x 214 mm D 255 61.5 MHzVideo Hdcp Resolution ModeSupported timing for Hdmi Hdcp input-MP512 ST Signal Format Supported timing for PC input-MP522 STWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive

MP512 ST, MP522 ST specifications

The BenQ MP522 ST and MP512 ST are compact projectors designed to deliver impressive performance for both education and business environments. These models stand out for their versatility, high-quality image output, and user-friendly features.

The BenQ MP522 ST is known for its Short Throw technology, enabling it to project large images from a short distance. This feature is particularly beneficial in smaller rooms where space is limited. The projector can produce a 60-inch image from just over two feet away, making it ideal for classroom settings and small meeting rooms. The MP522 ST boasts a brightness of 2800 ANSI lumens, ensuring clear and vibrant presentations even in well-lit environments. With a native resolution of XGA (1024 x 768), it delivers sharp and detailed visuals, making text and images easy to read.

On the other hand, the BenQ MP512 ST shares many of the same features while offering slightly different specifications. The MP512 ST also uses Short Throw technology, allowing it to project large images in limited spaces. With a brightness of 2500 ANSI lumens, it provides adequate illumination for various settings. This projector also supports a native resolution of XGA, ensuring excellent image quality for presentations and videos.

Both projectors utilize DLP technology, known for its reliability and high-quality images. DLP projectors typically have better color accuracy and contrast ratios compared to other technologies, resulting in vivid and lifelike images. Furthermore, the long-lasting lamp life of up to 4000 hours in Eco mode enhances cost efficiency and reduces maintenance needs over time.

Another notable characteristic of both models is their connectivity options, which include multiple VGA inputs, a composite video input, and a USB port. This variety allows for easy connections to laptops, video sources, and even USB drives, making them versatile tools for presentations and multimedia sharing.

Both BenQ MP522 ST and MP512 ST projectors emphasize portability and ease of use. Their lightweight design and compact size make them easy to transport, while features such as automatic keystone correction simplify setup and ensure optimal image alignment.

In summary, the BenQ MP522 ST and MP512 ST projectors are excellent choices for users seeking high-quality, compact projectors with superior image performance. Their short throw capabilities, robust brightness, and extended lamp life, coupled with DLP technology, make them reliable solutions for a range of applications in education and business environments.