BenQ MP522 ST, MP512 ST Personalizing the projector menu display, Shutting down the projector

Page 40

Personalizing the projector menu display

The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance.

Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length

ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame.

Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position.

Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language.

Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen.

Shutting down the projector

1. Press II Power and a confirmation message displays prompting you.

If you don't respond in a few seconds, the message will disappear.

2. Press II Power a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector.

3. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. The POWER indicator light is a steady orange and fans stop.

4.Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time.

To turn off the power ring tone, see "Turning off the Power on/off ring tone" on page 39 for details.

To protect the lamp, the projector will not respond to any commands during the cooling process.

To shorten the cooling time, you can also activate the Quick Cooling function. See "Quick Cooling" on page 46 for details.

Do not unplug the power cord before the projector shutdown sequence is complete or during the 90-second cooling down process.

If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press Power again to start the projector after the fans stop and the POWER indicator light turns orange.

40 Operation

Image 40
Contents Welcome MP512 ST/MP522 ST Digital ProjectorTable of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector This Apparatus Must be EarthedIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideMP522 ST MP512 ST External control panelControls and functions ProjectorRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Positioning your projector Choosing a locationObtaining a preferred projected image size Page Projection dimensions Connecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorConnecting Video source devices Connecting audioBest video quality Better video qualityConnecting an Hdmi device To connect the projector to an Hdmi deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceComponent Video to VGA D-Sub adaptor cable Audio cable To connect the projector to an S-Video source device Connecting an S-Video source deviceCable Video cable To connect the projector to a composite Video source device Connecting a composite Video source deviceAudio cable Video cable Starting up the projector OperationOperation Using the menus Use / to highlight the System Setup Basic menuUtilizing the password function Setting a passwordIf you forget the password Security SettingsEntering the password recall procedure Changing the passwordDisabling the password function Enter a new passwordSignal Switching input signalChanging color space Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioSelecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp. analog RGB Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightHow to use the Timer On key? To cancel the timer, perform the following stepsHiding the image Utilizing FAQ function Or go to the System Setup Basic PanelLocking control keys Freezing the imageAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Basic LanguageSystem Setup Advanced Picture ModeEquivalent lamp hour SecurityDescription of each menu Temperature Save SettingsTimer Auto PowerSleep Timer SettingsPanel Key LockSystem Setup Advanced menu Reset AllLamp SecurityFAQ-Image Installation Features ServiceInformation menu CurrentMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Resetting the lamp timer Setup Advanced Lamp Settings menuDisplays. Press to highlight Reset lamp Tighten the screw that secures the lampIndicators Troubleshooting Specifications Projector specificationsDimensions Refresh rate Horizontal Clock Resolution ModeMm W x 90 mm H x 214 mm D 255 61.5 MHzSupported timing for Hdmi Hdcp input-MP512 ST Resolution ModeVideo Hdcp Signal Format Supported timing for PC input-MP522 STWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive

MP512 ST, MP522 ST specifications

The BenQ MP522 ST and MP512 ST are compact projectors designed to deliver impressive performance for both education and business environments. These models stand out for their versatility, high-quality image output, and user-friendly features.

The BenQ MP522 ST is known for its Short Throw technology, enabling it to project large images from a short distance. This feature is particularly beneficial in smaller rooms where space is limited. The projector can produce a 60-inch image from just over two feet away, making it ideal for classroom settings and small meeting rooms. The MP522 ST boasts a brightness of 2800 ANSI lumens, ensuring clear and vibrant presentations even in well-lit environments. With a native resolution of XGA (1024 x 768), it delivers sharp and detailed visuals, making text and images easy to read.

On the other hand, the BenQ MP512 ST shares many of the same features while offering slightly different specifications. The MP512 ST also uses Short Throw technology, allowing it to project large images in limited spaces. With a brightness of 2500 ANSI lumens, it provides adequate illumination for various settings. This projector also supports a native resolution of XGA, ensuring excellent image quality for presentations and videos.

Both projectors utilize DLP technology, known for its reliability and high-quality images. DLP projectors typically have better color accuracy and contrast ratios compared to other technologies, resulting in vivid and lifelike images. Furthermore, the long-lasting lamp life of up to 4000 hours in Eco mode enhances cost efficiency and reduces maintenance needs over time.

Another notable characteristic of both models is their connectivity options, which include multiple VGA inputs, a composite video input, and a USB port. This variety allows for easy connections to laptops, video sources, and even USB drives, making them versatile tools for presentations and multimedia sharing.

Both BenQ MP522 ST and MP512 ST projectors emphasize portability and ease of use. Their lightweight design and compact size make them easy to transport, while features such as automatic keystone correction simplify setup and ensure optimal image alignment.

In summary, the BenQ MP522 ST and MP512 ST projectors are excellent choices for users seeking high-quality, compact projectors with superior image performance. Their short throw capabilities, robust brightness, and extended lamp life, coupled with DLP technology, make them reliable solutions for a range of applications in education and business environments.