BenQ MP511 user manual Connecting a Component Video source device

Page 22

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with

a D-Sub type connector) to the D-SUB socket on the projector.

The final connection path should be like that shown in the following diagram:

A/V device

Component Video to VGA (D-Sub) adaptor cable

If you connect the projector to a High Definition TV (HDTV) tuner, the following standards are supported:

•	480i	•	480p
•	576i	•	576p
•	720p (50/ 60 Hz)	•	1080i (50/ 60 Hz)

• Component Video is the only video output that delivers native 16:9 aspect ratio picture.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

22 Connection

Image 22

Contents Welcome Table of contents Troubleshooting Specifications MaintenanceMagnifying and searching for details Regulation statements Future reference Projector lamp is on Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorSafety Instructions Allow at least 50 cm clearance from walls Bedding or any other soft surface3000 m Resulting in damage to the projector Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Rear side Projector exterior viewFront/upper side Under viewControls and functions ProjectorAuto Right/Panel Key LockTimer Setup Remote controlTimer On RightReplacing the remote control battery Remote control effective rangePull out the battery holder Positioning your projector Choosing a locationObtaining a preferred projected image size Page Screen Diagonal Screen Center of lens Projection distanceTo connect the projector to a laptop or desktop computer Connecting a computerConnection ConnectionBetter video quality Connecting Video source devicesBest video quality Least video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video or a composite Video source device To connect the projector to an S-Video source deviceStart up OperationOperation If you forget the password Utilizing the power-on lock functionSetting a password Buttons Up , Right, DownDisabling the power-on lock function Entering the password recall procedureChanging the password Enter the old passwordSwitching input signal Go to Source Quick Auto Search menuAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityPress to correct keystoning at the bottom of the image Correcting keystoneFor example Selecting the aspect ratio Go to the Picture Picture Mode menu Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageAdjusting brightness Using Wall ColorFine-tuning the image quality in user modes Adjusting contrastAbout color temperatures 3D Color ManagementSetting the presentation timer Other adjustmentsHiding the image How to use the Timer On button?Button is a multi-functional key Locking control keys Freezing the imageUtilizing FAQ function Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorPC source Dynamic Menu operationMenu system Video source DynamicAdvanced Lamp mode Normal/EconomicBasic LanguageInformation Source Status Press Using the menusUse Left/ Right to select the Display menu Display menu Picture menu System setup Basic menu Source menuSystem setup Advanced menu Lamp Reset AllSecurity Information menu Maintenance Care of the projectorLamp information Calculation of lamp hourReplacing the lamp Page Tighten the screw that secures the lamp Temperature informationRestart the projector Powering up IndicatorsStand-by mode IllustrationLight Status & Description Power Temp Lamp Thermal events Troubleshooting Specifications Projector specificationsSupported timing for Component-YPbPrinput Timing chartSupported timing for PC input Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive