BenQ MP511 user manual Connecting an S-Video or a composite Video source device

Page 23

Connecting an S-Video or a composite Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

If you have already made a Component Video connection between the projector and the video source device, you need not connect to this device again using an S-Video or composite Video connection as this makes an unnecessary second connection of poorer picture quality. You need only connect using a composite Video connection if both Component Video and S- Video are not supplied on the video source device (for example, with some analog video cameras).

See "Connecting Video source devices" on page 21 for details.

To connect the projector to an S-Video source device:

1.Take an S-Video cable/Video cable and connect one end to the S-Video/Video output socket of the Video source device.

2.Connect the other end of the S-Video cable/Video Cable to the S-VIDEO/VIDEO

socket on the projector.

The final connection path should be like that shown in the following diagram:

A/V device

Video cable or S-Video cable

If the selected video picture is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 23

Image 23

Contents Welcome Table of contents Magnifying and searching for details MaintenanceTroubleshooting Specifications Regulation statements Do not look straight at the projector Important safety instructionsRefer servicing to qualified service personnel Future reference Projector lamp is onSafety Instructions 3000 m Resulting in damage to the projector Bedding or any other soft surfaceAllow at least 50 cm clearance from walls Ceiling mounting the projector Introduction Projector featuresIntroduction Shipping contents Under view Projector exterior viewFront/upper side Rear sideProjector Controls and functionsRight/Panel Key Lock AutoRight Remote controlTimer On Timer SetupPull out the battery holder Remote control effective rangeReplacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size Page Screen Center of lens Projection distance Screen DiagonalConnection Connecting a computerConnection To connect the projector to a laptop or desktop computerLeast video quality Connecting Video source devicesBest video quality Better video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video or a composite Video source deviceOperation OperationStart up Buttons Up , Right, Down Utilizing the power-on lock functionSetting a password If you forget the passwordEnter the old password Entering the password recall procedureChanging the password Disabling the power-on lock functionGo to Source Quick Auto Search menu Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageFor example Correcting keystonePress to correct keystoning at the bottom of the image Selecting the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting contrast Using Wall ColorFine-tuning the image quality in user modes Adjusting brightness3D Color Management About color temperaturesOther adjustments Setting the presentation timerButton is a multi-functional key How to use the Timer On button?Hiding the image Freezing the image Locking control keysOperating in a high altitude environment Utilizing FAQ functionShutting down the projector Personalizing the projector menu displayVideo source Dynamic Menu operationMenu system PC source DynamicLanguage Lamp mode Normal/EconomicBasic AdvancedInformation Source Use Left/ Right to select the Display menu Using the menusStatus Press Display menu Picture menu Source menu System setup Basic menuSystem setup Advanced menu Security Reset AllLamp Information menu Care of the projector MaintenanceCalculation of lamp hour Lamp informationReplacing the lamp Page Restart the projector Temperature informationTighten the screw that secures the lamp Illustration IndicatorsStand-by mode Powering upLight Status & Description Power Temp Lamp Thermal events Troubleshooting Projector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputDisclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statement