BenQ W1500 user manual Connecting Hdmi devices

Page 22

Connecting HDMI devices

Connecting HDMI devices to the projector with HDMI cables

HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible devices like DTV tuners, DVD players, Blu-ray players and displays over a single cable. It provides pure digital viewing and listening experience. You should use an HDMI cable when making connection between the projector and HDMI devices.

HDMI device: DVD player, digital tuner, etc.

To make sure you select a correct input source type for the HDMI signal, see "HDMI Settings" on page 55 for details.

HDMI cable

Connecting HDMI devices to the projector wirelessly

You may also make a wireless connection between the projector and HDMI devices. As your projector is equipped with the built-in HDMI receiver, when you plug the supplied wireless HDMI transmitter into any HDMI devices, the projector will display the contents from the connected HDMI source. See "Using the Wireless Transmitter" on page 25 for details.

To prevent signal interference with the projected image, while using this projector, please make sure that there are no other devices which support 5GHz wireless signals within 3 meters from the projector, such as access points/routers, wireless cards/dongles, 5.8GHz wireless mouses, 5.8GHz digital phones, some Wimax products, some Autopass cards, or devices with 802.11AC Wi-Fi.

Since different power of your wireless/radiation devices which operate in the 5GHz frequency band (e.g. industrial routers or home digital phones, etc.) will potentially impact projected image, the suggested distance could be over 3 meters away from the projector.

HDMI device: DVD player, digital tuner, etc.

Wireless HDMI transmitter

 

To connect the HDMI signal, select "Wireless"

 

from the source selection bar. See "Selecting an

Transmitter USB adapter

input source" on page 30 for details.

 

22 Important safety instructions

Image 22
Contents W1500 Digital Projector Home Cinema Series Table of contents Warranty and Copyright information Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control effective range Replacing the remote control batteriesCeiling mounting the projector Important safety instructions Projector features RS-232 control port Projector exterior viewFront and upper side view Rear and lower side view Audio L/R input jacksControls and functions Control panelRemote control Positioning your projector Choosing a locationObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Important safety instructions Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D Lowest Highest Installation for a 43 ratio screenFloor Installation Ceiling Installation Screen aspect ratio is 43 and the projected picture isShifting the projection lens vertically To use the lens shift leverConnecting with video equipment PreparationsConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableProduct specification Using the Wireless TransmitterSupported timing for wireless Hdmi input timing Message and meaning Power indicatorMode Refresh rate Hz Frequency kHz Clock MHz StatusWhen the Select Video Source menu displays, select Settings Wireless transmitter synchronizationSet Wireless Sync to On Settings menu, select Add New Video SourceImportant safety instructions Turning the projector on Using the projectorPreparations Selecting an input source Sharpen the picture by rotating the focus ringUse / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password As the picture indicates, the four arrow keysDisabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Fine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode Setting the User 1/User 2/User 3 modeAdjusting Brightness Fine-tuning the picture qualityResetting the picture mode Adjusting ContrastAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Flesh ToneTo set a preferred color temperature Setting Black LevelSetting a preferred color temperature Advanced picture quality controlsAdjusting Brilliant Color Selecting a Gamma settingColor Management Setting 3D Comb Filter Setting Film ModeTo leave and save the settings, press MENU/EXIT Switching the left/right audio channels Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneSelecting the aspect ratio About the aspect ratioFreezing the image Using the test patternMagnifying and searching for details To activate High Altitude Mode Operating in a high altitude environmentUsing the OSD menu To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Connecting 3D video devices Watching 3D contentUsing the 3D menus Locking control keys Personalizing the projector menu displayTo lock the keys Turning the projector off On-Screen Display OSD structure Audio SetupOn-Screen Display OSD menus Main menu Sub-menu OptionsSystem Setup Auto Off DisplayAdvanced SetupInformation Picture -- Basic menu Function DescriptionAudio Setup menu Display menu System Setup menu Advanced Setup menuReset All Settings High Altitude ModePassword Test PatternInformation menu Additional information Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Press MODE/ENTER to dismiss the message Timing of replacing the lampUntil the next hour lamp warning appears DiminishedDo not turn on the power with lamp cover removed Replacing the lampResetting the lamp timer Connect the power and restart the projectorPower Temp Lamp Status & Description IndicatorsLamp Status & Description Your Blu-ray Disc is not in 3D TroubleshootingProblem Cause Remedy FormatSpecifications Dimensions Ceiling mount installationResolution Mode Refresh rate Freq. KHz Clock MHz Timing chartSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHz 1400 x SXGA+60 59.978 65.317 121.750Video Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHz Resolution Mode Refresh rate Hz Freq. KHz Clock MHzSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationWarranty Disclaimer
Related manuals
Manual 66 pages 57.13 Kb