BenQ W1500 On-Screen Display OSD menus, On-Screen Display OSD structure, Picture -- Basic

Page 49

On-Screen Display (OSD) menus

On-Screen Display (OSD) structure

Please note that the on-screen display (OSD) menus vary according to the signal type selected.

Main menu	Sub-menu	Options
Preset Mode	Cinema/Dynamic/Standard/User 1/User 2/User 3/3D/ISF Day/ISF Night

Picture -- Basic

User Mode

Management

Brightness	0–100

Contrast	0–100

Color	0–100

Tint	0–100

Sharpness	0/1/2

Flesh Tone	0–5

Color Temperature	Normal/Cool/Lamp Native/Warm

Frame Interpolation	Off/Low/Middle/High

Lamp Power	Normal/Economic/SmartEco

Black Level	0 IRE/7.5 IRE

		Clarity Control	Noise Reduction/Detail Enhancement

		Color Temperature Fine	Red Gain/Green Gain/Blue Gain/Red Offset/
	Advanced...	Tuning	Green Offset/Blue Offset
		Gamma Selection	1.6/1.8/2.0/2.2/2.4/2.5/2.6/2.8/BenQ

		Brilliant Color	On/Off

		Color Management	Primary Color/Hue/Gain/Saturation

	Reset Picture Settings

	SRS		On/Off

	Mute		On/Off

	Volume		0–10

Audio Setup	Treble		0–10
Audio Setup
	Bass		0–10

	L/R Switch		Auto/On/Off

	Power On/Off Ring		On/Off
	Tone		On/Off
	Tone

Important safety instructions

49

Image 49

Contents W1500 Digital Projector Home Cinema Series Table of contents Warranty and Copyright information Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Overview Shipping contentsRemote control effective range Replacing the remote control batteriesCeiling mounting the projector Important safety instructions Projector features Front and upper side view Rear and lower side view Projector exterior viewRS-232 control port Audio L/R input jacksControl panel Controls and functionsRemote control Choosing a location Positioning your projectorDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeImportant safety instructions Installation for a 169 ratio screen Projection dimensionsFloor Installation Ceiling Installation Installation for a 43 ratio screenScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isTo use the lens shift lever Shifting the projection lens verticallyPreparations Connecting with video equipmentConnecting Hdmi devices Connecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerProduct specification Using the Wireless TransmitterSupported timing for wireless Hdmi input timing Mode Refresh rate Hz Frequency kHz Clock MHz Power indicatorMessage and meaning StatusSet Wireless Sync to On Wireless transmitter synchronizationWhen the Select Video Source menu displays, select Settings Settings menu, select Add New Video SourceImportant safety instructions Turning the projector on Using the projectorPreparations Sharpen the picture by rotating the focus ring Selecting an input sourceUsing a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password As the picture indicates, the four arrow keysChanging the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeResetting the picture mode Fine-tuning the picture qualityAdjusting Brightness Adjusting ContrastAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Flesh ToneSetting a preferred color temperature Setting Black LevelTo set a preferred color temperature Advanced picture quality controlsAdjusting Brilliant Color Selecting a Gamma settingColor Management Setting 3D Comb Filter Setting Film ModeTo leave and save the settings, press MENU/EXIT Adjusting the sound level Adjusting the soundSwitching the left/right audio channels Turning off the Power On/Off Ring ToneAbout the aspect ratio Selecting the aspect ratioFreezing the image Using the test patternMagnifying and searching for details Operating in a high altitude environment To activate High Altitude ModeUsing the OSD menu To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Connecting 3D video devices Watching 3D contentUsing the 3D menus Locking control keys Personalizing the projector menu displayTo lock the keys Turning the projector off On-Screen Display OSD menus Audio SetupOn-Screen Display OSD structure Main menu Sub-menu OptionsDisplay System Setup Auto OffAdvanced SetupInformation Function Description Picture -- Basic menuAudio Setup menu Display menu Advanced Setup menu System Setup menuPassword High Altitude ModeReset All Settings Test PatternInformation menu Care of the projector Additional informationGetting to know the lamp hour Lamp informationExtending lamp life Until the next hour lamp warning appears Timing of replacing the lampPress MODE/ENTER to dismiss the message DiminishedReplacing the lamp Do not turn on the power with lamp cover removedConnect the power and restart the projector Resetting the lamp timerPower Temp Lamp Status & Description IndicatorsLamp Status & Description Problem Cause Remedy TroubleshootingYour Blu-ray Disc is not in 3D FormatSpecifications Ceiling mount installation DimensionsResolution Mode Refresh rate Freq. KHz Clock MHz Timing chartSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input 1400 x SXGA+60 59.978 65.317 121.750 Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHzVideo Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHz Resolution Mode Refresh rate Hz Freq. KHz Clock MHzSupported timing for Video and S-Video inputs Warranty Warranty and Copyright informationCopyright Disclaimer

Related manuals

Manual 66 pages 57.13 Kb