BenQ W1500 user manual Turning the projector off

Page 48

Turning the projector off

To turn the projector off, press POWER on the projector or

on the remote control and a warning message appears. Press the button again.

• The Power indicator light flashes orange and the fans run for about two minutes to cool the lamp. The projector will not respond to any commands until the cooling process is complete. Once the cooling process finishes, a "Power Off Ring Tone" will be heard.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 41 for details.

•Then, the Power indicator light is a steady orange once the cooling process has finished and fans stop.

•If the projector will not be used for an extended period, unplug the power cable from the power outlet.

•To protect the lamp, the projector will not respond to any commands during the cooling process.

Actual lamp life may vary due to different environmental conditions and usage.

48 Important safety instructions

Image 48

Contents W1500 Digital Projector Home Cinema Series Table of contents Warranty and Copyright information Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewReplacing the remote control batteries Remote control effective rangeCeiling mounting the projector Important safety instructions Projector features Projector exterior view Front and upper side view Rear and lower side viewRS-232 control port Audio L/R input jacksControls and functions Control panelRemote control Positioning your projector Choosing a locationObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Important safety instructions Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isShifting the projection lens vertically To use the lens shift leverConnecting with video equipment PreparationsConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableUsing the Wireless Transmitter Product specificationSupported timing for wireless Hdmi input timing Power indicator Mode Refresh rate Hz Frequency kHz Clock MHzMessage and meaning StatusWireless transmitter synchronization Set Wireless Sync to OnWhen the Select Video Source menu displays, select Settings Settings menu, select Add New Video SourceImportant safety instructions Using the projector Turning the projector onPreparations Selecting an input source Sharpen the picture by rotating the focus ringUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password As the picture indicates, the four arrow keysEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeFine-tuning the picture quality Resetting the picture modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Flesh ToneSetting Black Level Setting a preferred color temperatureTo set a preferred color temperature Advanced picture quality controlsSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film Mode Setting 3D Comb FilterTo leave and save the settings, press MENU/EXIT Adjusting the sound Adjusting the sound levelSwitching the left/right audio channels Turning off the Power On/Off Ring ToneSelecting the aspect ratio About the aspect ratioUsing the test pattern Freezing the imageMagnifying and searching for details To activate High Altitude Mode Operating in a high altitude environmentTo display the PIP window Using the remote control Using the OSD menuDisplaying more than one image source simultaneously Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu display Locking control keysTo lock the keys Turning the projector off Audio Setup On-Screen Display OSD menusOn-Screen Display OSD structure Main menu Sub-menu OptionsSystem Setup Auto Off DisplaySetup AdvancedInformation Picture -- Basic menu Function DescriptionAudio Setup menu Display menu System Setup menu Advanced Setup menuHigh Altitude Mode PasswordReset All Settings Test PatternInformation menu Additional information Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Until the next hour lamp warning appearsPress MODE/ENTER to dismiss the message DiminishedDo not turn on the power with lamp cover removed Replacing the lampResetting the lamp timer Connect the power and restart the projectorIndicators Power Temp Lamp Status & DescriptionLamp Status & Description Troubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications Dimensions Ceiling mount installationTiming chart Resolution Mode Refresh rate Freq. KHz Clock MHzSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHz 1400 x SXGA+60 59.978 65.317 121.750Resolution Mode Refresh rate Hz Freq. KHz Clock MHz Video Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHzSupported timing for Video and S-Video inputs Warranty and Copyright information WarrantyCopyright Disclaimer

Related manuals

Manual 66 pages 57.13 Kb