BenQ W1500 Timing of replacing the lamp, Until the next hour lamp warning appears, Diminished

Page 60

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://lamp.BenQ.com for a replacement lamp.

The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 63 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

Install a new lamp for optimal performance. If the projector is

WARNING

normally run with Economic selected (see "Getting to know the

 

lamp hour" on page 59), you may continue to operate the projector

NOTICE: Order replacement lamp

until the next hour lamp warning appears.

Lamp > XXXX hrs

Press MODE/ENTER to dismiss the message.

Order a new lamp at

lamp.benq.com

 

 

OK

 

 

It is strongly recommended that you replace the lamp at this stage.

WARNING

The lamp is a consumable item. The lamp brightness diminishes with

 

use. This is normal lamp behavior. You can replace the lamp

NOTICE: Replace lamp soon

whenever you notice that the brightness level has significantly

Lamp > XXXX hrs

diminished.

Order a new lamp at

Press MODE/ENTER to dismiss the message.

lamp.benq.com

OK

 

 

The lamp MUST be replaced before the projector will operate

WARNING

normally.

NOTICE: Replace lamp now

Press MODE/ENTER to dismiss the message.

Lamp > XXXX hrs

Lamp-usage time exceeded

 

Replace lamp (refer to User’s Manual)

 

then reset lamp timer.

 

Order a new lamp at

 

lamp.benq.com

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

60 Important safety instructions

Page 59 Page 61
Image 60
Page 59 Page 61
Contents W1500 Digital Projector Home Cinema Series Table of contents Warranty and Copyright information Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewReplacing the remote control batteries Remote control effective rangeCeiling mounting the projector Important safety instructions Projector features Projector exterior view Front and upper side view Rear and lower side viewRS-232 control port Audio L/R input jacksControls and functions Control panelRemote control Positioning your projector Choosing a locationObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Important safety instructions Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isShifting the projection lens vertically To use the lens shift leverConnecting with video equipment PreparationsConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableUsing the Wireless Transmitter Product specificationSupported timing for wireless Hdmi input timing Power indicator Mode Refresh rate Hz Frequency kHz Clock MHzMessage and meaning StatusWireless transmitter synchronization Set Wireless Sync to OnWhen the Select Video Source menu displays, select Settings Settings menu, select Add New Video SourceImportant safety instructions Using the projector Turning the projector onPreparations Selecting an input source Sharpen the picture by rotating the focus ringUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password As the picture indicates, the four arrow keysEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeFine-tuning the picture quality Resetting the picture modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Flesh ToneSetting Black Level Setting a preferred color temperatureTo set a preferred color temperature Advanced picture quality controlsSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film Mode Setting 3D Comb FilterTo leave and save the settings, press MENU/EXIT Adjusting the sound Adjusting the sound levelSwitching the left/right audio channels Turning off the Power On/Off Ring ToneSelecting the aspect ratio About the aspect ratioUsing the test pattern Freezing the imageMagnifying and searching for details To activate High Altitude Mode Operating in a high altitude environmentTo display the PIP window Using the remote control Using the OSD menuDisplaying more than one image source simultaneously Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu display Locking control keysTo lock the keys Turning the projector off Audio Setup On-Screen Display OSD menusOn-Screen Display OSD structure Main menu Sub-menu OptionsSystem Setup Auto Off DisplaySetup AdvancedInformation Picture -- Basic menu Function DescriptionAudio Setup menu Display menu System Setup menu Advanced Setup menuHigh Altitude Mode PasswordReset All Settings Test PatternInformation menu Additional information Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Until the next hour lamp warning appearsPress MODE/ENTER to dismiss the message DiminishedDo not turn on the power with lamp cover removed Replacing the lampResetting the lamp timer Connect the power and restart the projectorIndicators Power Temp Lamp Status & DescriptionLamp Status & Description Troubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications Dimensions Ceiling mount installationTiming chart Resolution Mode Refresh rate Freq. KHz Clock MHzSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHz 1400 x SXGA+60 59.978 65.317 121.750Resolution Mode Refresh rate Hz Freq. KHz Clock MHz Video Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHzSupported timing for Video and S-Video inputs Warranty and Copyright information WarrantyCopyright Disclaimer
Related manuals
Manual 66 pages 57.13 Kb
Top Page Image Contents