BenQ W1500 Fine-tuning the picture quality, Resetting the picture mode, Adjusting Brightness

Page 36

5.Press to highlight a picture mode that is closest to your need and press MODE/ENTER and MENU/EXIT to go back to the User Mode Management page.

6.Here you can rename the User 1, User 2, or User 3 mode by pressing to highlight Rename User Mode and press MODE/ENTER. The Rename User Mode page displays.

7.Press /// until your desired character is selected and press MODE/ENTER.

8.Press MENU/EXIT to go back to the main menu once you are done.

9.Press to select a sub-menu item to be changed and adjust the value with / . See "Fine-tuning the picture quality" on page 36 and "Advanced picture quality controls" on page 38 for details.

10.When all settings have been done, press MENU/EXIT to save and leave the settings.

Resetting the picture mode

All of the adjustments you’ve done in the Picture -- Basic menus can be returned to the factory preset values with a key press on the highlight of Reset.

To reset the picture mode to the preset factory values:

1.In the Picture -- Basic menu, highlight Preset Mode and press / to select the picture mode (including User 1, User 2, or User 3) you want to reset.

2.Press to highlight Reset Picture Settings and press MODE/ENTER. The confirmation message displays.

3.Press / to highlight Reset and press MODE/ENTER. The picture mode will return to the factory preset settings.

4.Repeat steps 1-3if you want to reset other picture modes.

Do not to be confused with the Reset Picture Settings function here with the Reset All Settings in the Advanced Setup menu. The Reset All Settings function returns most of the settings to the factory preset values system wide. See "Reset All Settings" on page 56 for details.

Fine-tuning the picture quality

No matter what picture mode you have selected, you are able to fine-tune those settings to fit every presentation purpose. Those adjustments will be saved to the preset mode you are at when you exit the OSD menu.

Adjusting Brightness

Highlight Brightness in the Picture -- Basic menu and adjust the values by pressing / on the projector or remote control.

The higher the value, the brighter the picture. And the

30

50

70

 

lower the setting, the darker the picture. Adjust this

control so the black areas of the picture appear just as black and that detail in the dark areas is visible.

Adjusting Contrast

Highlight Contrast in the Picture -- Basic menu and

 

 

 

 

adjust the values by pressing /

on the projector or

 

 

 

 

remote control.

 

 

 

 

 

The higher the value, the greater the contrast. Use this to

 

 

 

30

 

 

 

 

set the peak white level after you have previously adjusted

 

 

 

 

the Brightness setting to suit your selected input and viewing environment.

50

70

36 Important safety instructions

Page 35 Page 37
Image 36
Page 35 Page 37
Contents W1500 Digital Projector Home Cinema Series Table of contents Warranty and Copyright information Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewReplacing the remote control batteries Remote control effective rangeCeiling mounting the projector Important safety instructions Projector features Projector exterior view Front and upper side view Rear and lower side viewRS-232 control port Audio L/R input jacksControls and functions Control panelRemote control Positioning your projector Choosing a locationObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Important safety instructions Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isShifting the projection lens vertically To use the lens shift leverConnecting with video equipment PreparationsConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableUsing the Wireless Transmitter Product specificationSupported timing for wireless Hdmi input timing Power indicator Mode Refresh rate Hz Frequency kHz Clock MHzMessage and meaning StatusWireless transmitter synchronization Set Wireless Sync to OnWhen the Select Video Source menu displays, select Settings Settings menu, select Add New Video SourceImportant safety instructions Using the projector Turning the projector onPreparations Selecting an input source Sharpen the picture by rotating the focus ringUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password As the picture indicates, the four arrow keysEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeFine-tuning the picture quality Resetting the picture modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Flesh ToneSetting Black Level Setting a preferred color temperatureTo set a preferred color temperature Advanced picture quality controlsSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film Mode Setting 3D Comb FilterTo leave and save the settings, press MENU/EXIT Adjusting the sound Adjusting the sound levelSwitching the left/right audio channels Turning off the Power On/Off Ring ToneSelecting the aspect ratio About the aspect ratioUsing the test pattern Freezing the imageMagnifying and searching for details To activate High Altitude Mode Operating in a high altitude environmentTo display the PIP window Using the remote control Using the OSD menuDisplaying more than one image source simultaneously Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu display Locking control keysTo lock the keys Turning the projector off Audio Setup On-Screen Display OSD menusOn-Screen Display OSD structure Main menu Sub-menu OptionsSystem Setup Auto Off DisplaySetup AdvancedInformation Picture -- Basic menu Function DescriptionAudio Setup menu Display menu System Setup menu Advanced Setup menuHigh Altitude Mode PasswordReset All Settings Test PatternInformation menu Additional information Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Until the next hour lamp warning appearsPress MODE/ENTER to dismiss the message DiminishedDo not turn on the power with lamp cover removed Replacing the lampResetting the lamp timer Connect the power and restart the projectorIndicators Power Temp Lamp Status & DescriptionLamp Status & Description Troubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications Dimensions Ceiling mount installationTiming chart Resolution Mode Refresh rate Freq. KHz Clock MHzSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHz 1400 x SXGA+60 59.978 65.317 121.750Resolution Mode Refresh rate Hz Freq. KHz Clock MHz Video Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHzSupported timing for Video and S-Video inputs Warranty and Copyright information WarrantyCopyright Disclaimer
Related manuals
Manual 66 pages 57.13 Kb
Top Page Image Contents