BenQ W1500 user manual Setting Film Mode, Setting 3D Comb Filter

Page 40

1.In the Picture -- Basic > Advanced... menu, highlight Color Management and press MODE/ENTER. The Color Management page displays.

2.Highlight Primary Color and press / to select a color from among Red, Green, Blue, Cyan, Magenta and Yellow.

3.Press to highlight Hue and press / to select its range. Increase in the range will include colors consisted of more proportions of its two adjacent colors.

Red Yellow Green

Magenta Cyan

Blue

Please refer to the illustration to the right for how the colors relate to each other. For example, if you select Red and set its range at 0,

only pure red is selected. Increasing its range will include both the red color close to yellow and red color close to magenta.

4.Press to highlight Gain and adjust its values to your preference by pressing / . The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.

5.Press to highlight Saturation and adjust its values to your preference by pressing / . Every adjustment made will reflect to the image immediately.

For example, if you select Red and set its value at 0, only the saturation of pure red will be affected.

Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

6. To leave and save the settings, press MENU/EXIT.

Setting Film Mode

Highlight Film Mode in the Display menu and select On by pressing / on the projector or remote control.

This feature helps improve picture quality when projecting composite or S-video image from a film- sourced DVD or Blu-ray Disc.

Setting 3D Comb Filter

Highlight 3D Comb Filter in the Display menu and select On by pressing / on the projector or remote control.

This feature separates composite signal to Y (brightness) signal and C (color) signal, and can help produce clearer and sharper images with correct colors in place.

This function is only available when a composite signal is selected.

40 Important safety instructions

Image 40
Contents W1500 Digital Projector Home Cinema Series Table of contents Warranty and Copyright information Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control effective range Replacing the remote control batteriesCeiling mounting the projector Important safety instructions Projector features Projector exterior view Front and upper side view Rear and lower side viewRS-232 control port Audio L/R input jacksControls and functions Control panelRemote control Positioning your projector Choosing a locationObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Important safety instructions Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isShifting the projection lens vertically To use the lens shift leverConnecting with video equipment PreparationsConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableProduct specification Using the Wireless TransmitterSupported timing for wireless Hdmi input timing Power indicator Mode Refresh rate Hz Frequency kHz Clock MHzMessage and meaning StatusWireless transmitter synchronization Set Wireless Sync to OnWhen the Select Video Source menu displays, select Settings Settings menu, select Add New Video SourceImportant safety instructions Turning the projector on Using the projectorPreparations Selecting an input source Sharpen the picture by rotating the focus ringUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password As the picture indicates, the four arrow keysEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeFine-tuning the picture quality Resetting the picture modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Flesh ToneSetting Black Level Setting a preferred color temperatureTo set a preferred color temperature Advanced picture quality controlsAdjusting Brilliant Color Selecting a Gamma settingColor Management Setting 3D Comb Filter Setting Film ModeTo leave and save the settings, press MENU/EXIT Adjusting the sound Adjusting the sound levelSwitching the left/right audio channels Turning off the Power On/Off Ring ToneSelecting the aspect ratio About the aspect ratioFreezing the image Using the test patternMagnifying and searching for details To activate High Altitude Mode Operating in a high altitude environmentUsing the OSD menu To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Connecting 3D video devices Watching 3D contentUsing the 3D menus Locking control keys Personalizing the projector menu displayTo lock the keys Turning the projector off Audio Setup On-Screen Display OSD menusOn-Screen Display OSD structure Main menu Sub-menu OptionsSystem Setup Auto Off DisplayAdvanced SetupInformation Picture -- Basic menu Function DescriptionAudio Setup menu Display menu System Setup menu Advanced Setup menuHigh Altitude Mode PasswordReset All Settings Test PatternInformation menu Additional information Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Until the next hour lamp warning appearsPress MODE/ENTER to dismiss the message DiminishedDo not turn on the power with lamp cover removed Replacing the lampResetting the lamp timer Connect the power and restart the projectorPower Temp Lamp Status & Description IndicatorsLamp Status & Description Troubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications Dimensions Ceiling mount installationResolution Mode Refresh rate Freq. KHz Clock MHz Timing chartSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHz 1400 x SXGA+60 59.978 65.317 121.750Video Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHz Resolution Mode Refresh rate Hz Freq. KHz Clock MHzSupported timing for Video and S-Video inputs Warranty and Copyright information WarrantyCopyright Disclaimer
Related manuals
Manual 66 pages 57.13 Kb