BenQ MX850UST, MW851UST user manual Remote control, On/Off, Test, Keystone/Arrow buttons / Up Down

Page 11

Remote control

1

13

2

 

14

3

15

4

16

 

5

17

6

16

 

7

18

8

19

9

20

10

21

11

22

 

12

23

 

24

1. ON/OFF

Toggles the projector between standby mode and on.

2.Source selection buttons (COMPUTER-1, COMPUTER-2, VIDEO, S-VIDEO)

Selects an input source for display.

3.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

4.ECO BLANK

Used to hide the screen image.

5. Left

6.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

7.LASER

Emits visible laser pointer light for presentation purposes.

8.PAGE UP/PAGE DOWN

Operates your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

9.FREEZE

Freezes the projected image.

10.NETWORK SETTING

Enters network setting directly.

11.TEST

Displays the test pattern.

12.SMART ECO

Displays the lamp mode selection bar.

13.NETWORK

Searches the network signal and project it within a few seconds once available.

14.SOURCE

Displays the source selection bar.

15.Auto

Automatically determines the best picture timings for the displayed image.

16.Keystone/Arrow buttons ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

17. Right

When the On-Screen Display (OSD) menu is activated, the #5, #16 and #17 buttons are used as directional arrows to select the desired menu items and to make adjustments.

Introduction 11

Image 11
Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherInverted images for ceiling mount InstallationIntroduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Projector Keystone/Arrow buttons / Up Down Remote controlON/OFF TestNumeric buttons Operating the Laser pointerMute MIC/VOL +Replacing the remote control battery Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Obtaining a preferred projected image size Projection dimensions1778 1508 942 Screen Size Distance from Screen in mmDiagonal Inches 1524 808Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceDevice Audio Settings Microphone Volume menuPlaying sound through the projector About the microphone inputOperation OperationStarting up the projector Correcting keystone Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAspect alteration Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownLocking control keys Remote paging operationsFreezing the image Hiding the imageCreating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserIiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Hr/8 hr/12 hr System Setup BasicSleep Timer Min/25 min/30 minAdvanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsColor Space TimerSettings SearchLock Function DescriptionOperation Panel KeyLamp System Setup Advanced menu Function Description HighAltitude AudioNetwork System Setup Advanced menu Function DescriptionReset All StandbyStatus Information menu Function DescriptionCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out of the projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Troubleshooting Projector specifications SpecificationsMm W x 236.9 mm H x 322.8 mm D 339 Specifications DimensionsMinimum installation requirements Wall mount installation975 1173 1189 1181 960 Wall plate Minimum Ceiling Height mm = f + H + b + 60 + 221+ cCeiling Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputTiming Supported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright