BenQ MW851UST, MX850UST user manual Timing of replacing the lamp, Status Message

Page 52

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 56 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

Install a new lamp for optimal performance. If the

Notice

projector is normally run with Economic selected

 

(See "Getting to know the lamp hour" on page 51),

Order Replacement Lamp

you may continue to operate the projector until

Lamp>XXXX Hours

the next hour lamp warning appears.

 

Press MODE/ENTER to dismiss the message.

Order a new lamp at lamp.benq.com

 

 

OK

 

 

It is strongly recommended that you replace the

Notice

lamp at this age. The lamp is a consumable item.

 

The lamp brightness diminishes with use. This is

Replace Lamp Soon

normal lamp behavior. You can replace the lamp

 

whenever you notice that the brightness level has

Lamp>XXXX Hours

 

significantly diminished.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

Notice

 

Replace Lamp Now

 

Lamp>XXXX Hours

 

Order a new lamp at lamp.benq.com

 

OK

 

 

The lamp MUST be replaced before the projector

WARNING

will operate normally.

Out of Lamp Usage Time

Press MODE/ENTER to dismiss the message.

 

 

Replace lamp (refer to User Manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

52 Maintenance

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstallation Inverted images for ceiling mountIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Projector Remote control ON/OFFTest Keystone/Arrow buttons / Up DownOperating the Laser pointer MuteMIC/VOL + Numeric buttonsRemote control effective range Replacing the remote control batteryChoosing a location Positioning your projectorFront Ceiling Projection dimensions Obtaining a preferred projected image sizeScreen Size Distance from Screen in mm Diagonal Inches 1524808 1778 1508 942Connection Connecting video source devices Connecting audioTerminal name Terminal appearance BestAudio Settings Microphone Volume menu Playing sound through the projectorAbout the microphone input DeviceStarting up the projector OperationOperation Adjusting the projected image Auto-adjusting the imageFine-tuning the image clarity Correcting keystoneFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center About the aspect ratioScreen with a 169 aspect ratio Aspect alterationUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Freezing the imageHiding the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Direct power off Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options System Setup Basic Sleep TimerMin/25 min/30 min Hr/8 hr/12 hrAdvanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description TeachingTimer SettingsSearch Color SpaceFunction Description OperationPanel Key LockSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkInformation menu Function Description CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Light Status & Description Power events IndicatorsLamp events Troubleshooting Specifications Projector specificationsDimensions Mm W x 236.9 mm H x 322.8 mm D 339 SpecificationsWall mount installation Minimum installation requirements975 1173 1189 1181 960 Ceiling Minimum Ceiling Height mm = f + H + b + 60 + 221+ cWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputHorizontal Supported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer
Top Page Image Contents