BenQ MW851UST, MX850UST user manual Specifications, Projector specifications

Page 58

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution

MX850UST

1024 x 768 XGA

MW851UST

1280 x 800 WXGA

Display system 1-CHIP DMD

Lens F/Number

F = 2.59 Lamp

230 W lamp

Electrical

Power supply

AC100–240V, 3.3 A, 50-60 Hz (Automatic) Power consumption

397 W (Max); < 0.5 W (Standby)

Mechanical

Weight

5.3 Kg (11.7 lbs)

Output terminals

RGB output

D-Sub 15-pin (female) x 1 Speaker

(Stereo) 10 watt x 2 Audio signal output

PC audio jack x 1

Control

RS-232 serial control 9 pin x 1

IR receiver x 2

12V trigger x 1 (Max. 1A)

LAN control RJ45 x 1

USB port (Mini-B x 1)

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3 (through RGB input)

Digital - HDMI V1.3 x 1

Audio signal input Audio in

PC audio jack x 2

RCA audio jack (L/R) x 2 Microphone x 1

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

58 Specifications

Image 58
Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceInstallation Inverted images for ceiling mountIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Projector Test Remote controlON/OFF Keystone/Arrow buttons / Up DownMIC/VOL + Operating the Laser pointerMute Numeric buttonsRemote control effective range Replacing the remote control batteryChoosing a location Positioning your projectorFront Ceiling Projection dimensions Obtaining a preferred projected image size808 Screen Size Distance from Screen in mmDiagonal Inches 1524 1778 1508 942Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestAbout the microphone input Audio Settings Microphone Volume menuPlaying sound through the projector DeviceStarting up the projector OperationOperation Fine-tuning the image clarity Adjusting the projected imageAuto-adjusting the image Correcting keystoneFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAbout the aspect ratio Aspect alterationSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Direct power off Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Min/25 min/30 min System Setup BasicSleep Timer Hr/8 hr/12 hrAdvanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSearch TimerSettings Color SpacePanel Key Function DescriptionOperation LockAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Light Status & Description Power events IndicatorsLamp events Troubleshooting Specifications Projector specificationsDimensions Mm W x 236.9 mm H x 322.8 mm D 339 SpecificationsWall mount installation Minimum installation requirements975 1173 1189 1181 960 Ceiling Minimum Ceiling Height mm = f + H + b + 60 + 221+ cWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputHorizontal Supported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer