BenQ MW851UST, MX850UST Using the menus, Following example describes how to set the OSD language

Page 22

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

Below is the overview of the OSD menu.

Main menu icon

Main menu

DISPLAY

Wall Color

Aspect Ratio

Keystone

Sub-menu

Position

Phase

H. Size

Digital Zoom

3D Sync

3D Sync Invert

Highlight

Teaching Template

Current input signal

Analog RGB

Off

Auto

On

ENTER

0

0

Off

Disable

MENU Exit

Status

Press MENU/ EXIT to the previous page or to exit.

The following example describes how to set the OSD language.

1.Press MENU/EXIT on the projector or remote control to turn the OSD menu on.

DISPLAY

Wall Color	Off
Aspect Ratio	Auto
Keystone	On
Position
Phase	0
H. Size	0
Digital Zoom
3D Sync	Off
3D Sync Invert	Disable
Teaching Template
Analog RGB	MENU Exit

3.Press to highlight Language

and press / to select a preferred language.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
My Screen

Analog RGB

MENU Exit

2.Use / to highlight the SYSTEM SETUP: Basic menu.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings	Off
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
My Screen

4.Press MENU/EXIT twice* on the projector or remote control to leave and save the settings.

*The first press leads you back to the main menu and the second press closes the OSD menu.

Analog RGB	MENU Exit

22 Operation

Image 22

Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceInstallation Inverted images for ceiling mountIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Projector Test Remote controlON/OFF Keystone/Arrow buttons / Up DownMIC/VOL + Operating the Laser pointerMute Numeric buttonsRemote control effective range Replacing the remote control batteryChoosing a location Positioning your projectorFront Ceiling Projection dimensions Obtaining a preferred projected image size808 Screen Size Distance from Screen in mmDiagonal Inches 1524 1778 1508 942Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestAbout the microphone input Audio Settings Microphone Volume menuPlaying sound through the projector DeviceStarting up the projector OperationOperation Fine-tuning the image clarity Adjusting the projected imageAuto-adjusting the image Correcting keystoneFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAbout the aspect ratio Aspect alterationSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Direct power off Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Min/25 min/30 min System Setup BasicSleep Timer Hr/8 hr/12 hrAdvanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSearch TimerSettings Color SpacePanel Key Function DescriptionOperation LockAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Light Status & Description Power events IndicatorsLamp events Troubleshooting Specifications Projector specificationsDimensions Mm W x 236.9 mm H x 322.8 mm D 339 SpecificationsWall mount installation Minimum installation requirements975 1173 1189 1181 960 Ceiling Minimum Ceiling Height mm = f + H + b + 60 + 221+ cWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputHorizontal Supported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer