BenQ MW851UST, MX850UST user manual Inverted images for ceiling mount, Installation

Page 6

Safety Instructions (Continued)

16.

Do not step on the projector or place

Ceiling mounting the projector

 

any objects upon it. Besides probable

 

 

 

physical damage to the projector, doing

We want you to have a pleasant

 

so may result in accidents and possible

experience using your BenQ projector,

 

injury.

so we need to bring this safety matter to

 

 

your attention to prevent possible

 

 

damage to person and property.

 

 

If you intend to mount your projector

 

 

on the ceiling, we strongly recommend

 

 

that you use a proper fitting BenQ

 

 

projector ceiling mount kit and that

 

 

you ensure it is securely and safely

 

 

installed.

17.

Do not place liquids near or on the

If you use a non-BenQ brand projector

ceiling mount kit, there is a safety risk

 

projector. Liquids spilled into the

 

that the projector may fall from the

 

projector may cause it to fail. If the

 

ceiling due to an improper attachment

 

projector does become wet, disconnect

 

through the use of the wrong gauge or

 

it from the power supply's power outlet

 

length screws.

 

and call BenQ to have the projector

 

You can purchase a BenQ projector

 

serviced.

 

ceiling mount kit from the place you

 

 

 

 

purchased your BenQ projector. BenQ

 

 

recommends that you also purchase a

 

 

separate Kensington lock compatible

 

 

security cable and attach it securely to

 

 

both the Kensington lock slot on the

 

 

projector and the base of the ceiling

 

 

mount bracket. This will perform the

 

 

secondary role of restraining the

 

 

projector should its attachment to the

 

 

mounting bracket become loose.

18.This product is capable of displaying

inverted images for ceiling mount

Hg - Lamp contains mercury. Manage in

installation.

accordance with local disposal laws.

Use only BenQ's Ceiling Mount Kit for

See www.lamprecycle.org.

 

mounting the projector and ensure it is

 

securely installed.

 

19.This apparatus must be earthed.

6 Important safety instructions

Image 6
Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceInstallation Inverted images for ceiling mountProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Projector Test Remote controlON/OFF Keystone/Arrow buttons / Up DownMIC/VOL + Operating the Laser pointerMute Numeric buttonsRemote control effective range Replacing the remote control batteryPositioning your projector Choosing a locationFront Ceiling Projection dimensions Obtaining a preferred projected image size808 Screen Size Distance from Screen in mmDiagonal Inches 1524 1778 1508 942Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestAbout the microphone input Audio Settings Microphone Volume menuPlaying sound through the projector DeviceOperation Starting up the projectorOperation Fine-tuning the image clarity Adjusting the projected imageAuto-adjusting the image Correcting keystoneUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAbout the aspect ratio Aspect alterationSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysTo activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen Adjusting the sound Controlling the projector through a LAN environmentCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Direct power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options Min/25 min/30 min System Setup BasicSleep Timer Hr/8 hr/12 hrAdvanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSearch TimerSettings Color SpacePanel Key Function DescriptionOperation LockAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out of the projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Indicators Light Status & Description Power eventsLamp events Troubleshooting Specifications Projector specificationsDimensions Mm W x 236.9 mm H x 322.8 mm D 339 SpecificationsWall mount installation Minimum installation requirements975 1173 1189 1181 960 Minimum Ceiling Height mm = f + H + b + 60 + 221+ c CeilingWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput TimingHorizontal Supported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer