BenQ MW851UST, MX850UST user manual Use the handle to slowly pull the lamp out of the projector

Page 54

8.Use the handle to slowly pull the lamp out of the projector.

•Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

•Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

•Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

9.As shown in the figure, lower the new lamp

first into the connector on the projector and reconnect the lamp connector.

10.Tighten the screw that secures the lamp.

11.Ensure the handle is fully laid flat and locked in place.

•Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screw.

12.Replace the new protection film that comes with the new lamp.

13.Replace the lamp cover on the projector.

1 2

14.Tighten the screws that secure the lamp cover.

•Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screw.

54 Maintenance

Image 54

Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceInstallation Inverted images for ceiling mountProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Projector Test Remote controlON/OFF Keystone/Arrow buttons / Up DownMIC/VOL + Operating the Laser pointerMute Numeric buttonsRemote control effective range Replacing the remote control batteryPositioning your projector Choosing a locationFront Ceiling Projection dimensions Obtaining a preferred projected image size808 Screen Size Distance from Screen in mmDiagonal Inches 1524 1778 1508 942Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestAbout the microphone input Audio Settings Microphone Volume menuPlaying sound through the projector DeviceOperation Starting up the projectorOperation Fine-tuning the image clarity Adjusting the projected imageAuto-adjusting the image Correcting keystoneUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAbout the aspect ratio Aspect alterationSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysTo activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen Adjusting the sound Controlling the projector through a LAN environmentCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Press Exit to go back to the remote network operation Direct power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options Min/25 min/30 min System Setup BasicSleep Timer Hr/8 hr/12 hrAdvanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSearch TimerSettings Color SpacePanel Key Function DescriptionOperation LockAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem Information menu Function DescriptionCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out of the projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Indicators Light Status & Description Power eventsLamp events Troubleshooting Specifications Projector specificationsDimensions Mm W x 236.9 mm H x 322.8 mm D 339 SpecificationsWall mount installation Minimum installation requirements975 1173 1189 1181 960 Minimum Ceiling Height mm = f + H + b + 60 + 221+ c CeilingWall plate Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput TimingHorizontal Supported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer