BenQ MX850UST, MW851UST user manual Description of each menu

Page 43

Description of each menu

1. DISPLAY menu

Function

Description

Wall Color

Corrects the projected picture’s color when the projection surface is not

white. See "Using Wall Color" on page 29 for details.

 

 

 

Aspect Ratio

There are several options to set the image's aspect ratio depending on

your input signal source. See "Selecting the aspect ratio" on page 27 for

 

details.

 

 

Keystone

Corrects any keystoning of the image. See "Correcting keystone" on

page 21 for details.

 

 

 

 

Displays the position adjustment page. To move the projected image,

 

use the directional arrow keys. The values shown on the lower position

Position

of the page change with every key press you made until they reach their

maximum or minimum.

 

This function is only available when a PC signal (analog RGB) is

 

selected.

 

Adjusts the clock phase to reduce image

 

distortion.

Phase

 

 

This function is only available when a PC

 

signal (analog RGB) is selected.

H. Size

Adjusts the horizontal width of the image.

This function is only available when a PC signal (analog RGB) is

 

selected.

Digital Zoom

Magnifies or reduces the projected image. See "Magnifying and

searching for details" on page 27 for details.

 

 

 

 

This projector features a 3D function which enables you to enjoy the

 

3D movies, videos, and sporting events in a more realistic way by

 

presenting the depth of the images. You need to wear a pair of 3D

 

glasses to view the 3D images.

 

Video timing: 480i

 

PC timing: up to 1280x800@120Hz for Frame Sequential

3D Sync

PC timing: up to 1280x800@60Hz for Frame Sequential

 

PC timing: up to SXGA+@60Hz for Top-Bottom

 

When the 3D Sync function is on:

 

• The brightness level of the projected image will decrease.

 

• The Picture Mode cannot be adjusted.

 

The Keystone can only be adjusted within limited degrees.

3D Sync

When you discover the inversion of the image depth, enable this

Invert

function to correct the problem.

 

 

Operation 43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherInverted images for ceiling mount InstallationIntroduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Projector Keystone/Arrow buttons / Up Down Remote controlON/OFF TestNumeric buttons Operating the Laser pointerMute MIC/VOL +Replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorFront Ceiling Obtaining a preferred projected image size Projection dimensions1778 1508 942 Screen Size Distance from Screen in mmDiagonal Inches 1524 808Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceDevice Audio Settings Microphone Volume menuPlaying sound through the projector About the microphone inputStarting up the projector OperationOperation Correcting keystone Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAspect alteration Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownLocking control keys Remote paging operationsFreezing the image Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen Controlling the projector through a LAN environment Adjusting the soundCable connection If you are in a non-DHCP environment Controlling the projector remotely through a web browserIiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options Hr/8 hr/12 hr System Setup BasicSleep Timer Min/25 min/30 minAdvanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsColor Space TimerSettings SearchLock Function DescriptionOperation Panel KeyLamp System Setup Advanced menu Function Description HighAltitude AudioNetwork System Setup Advanced menu Function DescriptionReset All StandbyStatus Information menu Function DescriptionCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out of the projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Light Status & Description Power events IndicatorsLamp events Troubleshooting Projector specifications SpecificationsMm W x 236.9 mm H x 322.8 mm D 339 Specifications DimensionsMinimum installation requirements Wall mount installation975 1173 1189 1181 960 Ceiling Minimum Ceiling Height mm = f + H + b + 60 + 221+ cWall plate Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputHorizontal Supported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents