BenQ MX880UST user manual Remote control, Test, Auto, Keystone/Arrow buttons / Up Down

Page 11

Remote control

1
2	12
	13
3	14
4
	15
5	16
6
	15
7	17
8	18
9	19
	20
10

11	21
11
	22
	23

1.ON/OFF

Toggles the projector between standby mode and on.

2.Source selection buttons (COMPUTER-1, COMPUTER-2, VIDEO, S-VIDEO)

Selects an input source for display.

3.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

4.BLANK

Used to hide the screen image.

5. Left/

Starts the FAQ function.

6.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

7.LASER

Emits visible laser pointer light for presentation purposes.

8.PAGE UP/PAGE DOWN

Operate your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

9.FREEZE

Freezes the projected image.

10.NETWORK SETTING

Enters network setting directly.

11.TEST

Displays the test pattern.

12.NETWORK

Searches the network signal and project it within a few seconds once available.

13.SOURCE

Displays the source selection bar.

14.AUTO

Automatically determines the best picture timings for the displayed image.

15.Keystone/Arrow buttons ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

16. Right/

Locks the buttons on the projector.

When the On-Screen Display (OSD) menu is activated, the #5, #15 and #16 buttons are used as directional arrows to select the desired menu items and to make adjustments.

Introduction 11

Image 11

Contents MX880UST Model Name MX712 UST Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Confined. Allow at least 50 cm clearance Inverted images for ceiling mount InstallationIntroduction Projector featuresShipping contents Projector exterior view Controls and functions Keystone/Arrow buttons / Up Down Remote controlTest AutoNumeric buttons Operating the Laser pointerMute MIC/VOL +Operating the projector from the front Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection Component Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceAbout the microphone input Playing sound through the projectorPage Starting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Highlight Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function If you forget the passwordEntering the password recall procedure Changing the passwordSwitching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageCreating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Advanced Network Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsColor Splash System Setup Advanced menu Function Description Panel KeyLock BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure the lamp cover Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsWall mount installation DimensionsSupported timing for PC input Timing chartTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users