BenQ MX880UST user manual Confined. Allow at least 50 cm clearance

Page 5

Safety Instructions (Continued)

13.Do not place this projector in any of the 14. Do not block the ventilation holes.

following environments.

- Do not place this projector on a blanket,

- Space that is poorly ventilated or

bedding or any other soft surface.

- Do not cover this projector with a cloth

confined. Allow at least 50 cm clearance

from walls and free flow of air around

or any other item.

the projector.

- Do not place inflammables near the

- Locations where temperatures may

projector.

become excessively high, such as the

 

inside of a car with all windows rolled

 

up.

 

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.

 

If the ventilation holes are seriously

 

obstructed, overheating inside the

 

projector may result in a fire.

15.

Always place the projector on a level,

 

horizontal surface during operation.

 

- Do not use if tilted at an angle of more

- Locations near fire alarms

than 10 degrees left to right, nor at angle

- Locations with an ambient temperature

of more than 15 degrees front to back.

above 40°C / 104°F

Using the projector when it is not fully

- Locations where the altitudes are higher

horizontal may cause a malfunction of,

or damage to, the lamp.

than 3000 m (10000 feet).

 

3000 m

 

(10000 feet)

 

0 m

16. Do not stand the projector on end

(0 feet)

vertically. Doing so may cause the

 

 

projector to fall over, causing injury or

 

resulting in damage to the projector.

Important safety instructions

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents MX880UST Model Name MX712 UST Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Confined. Allow at least 50 cm clearance Inverted images for ceiling mount InstallationIntroduction Projector featuresShipping contents Projector exterior view Controls and functions Test Remote controlAuto Keystone/Arrow buttons / Up DownMute Operating the Laser pointerMIC/VOL + Numeric buttonsOperating the projector from the front Remote control effective rangeReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsConnection Connecting audio Connecting video source devicesTerminal name Terminal appearance Component Video Better Good NormalAbout the microphone input Playing sound through the projectorPage Starting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Highlight Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Disabling the password functionSwitching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageLocking control keys To activate the High Altitude ModeOperating in a high altitude environment Creating your own startup screenAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring ToneCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Advanced Network Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description TeachingTimer System Setup Basic menu Function Description Quick AutoSettings SearchLock System Setup Advanced menu Function Description Panel KeyBackground Color SplashReset All System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure the lamp cover Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsWall mount installation DimensionsSupported timing for PC input Timing chartTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive
Top Page Image Contents