BenQ MX880UST Muting the sound, Adjusting the sound level, Adjusting the microphone volume

Page 35

1.Press CAPTURE on the remote control.

2.A confirmation message displays. Press CAPTURE or MODE/ENTER again.

3.The message 'Screen Capturing...' displays while the projector is processing the picture. Please wait.

4.If the action is successful, you see the message 'Captured Succeeded' on the screen. The captured picture is saved as My Screen.

5.To view the captured picture displayed as the startup screen, set My Screen in the

SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.

•Using the OSD menu

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Basic menu is highlighted.

2.Press to highlight MyScreen and press MODE/ENTER.

3.Repeat steps 2-5 in the “Using the remote control” section to capture and view the captured picture.

In the unlikely event that the capturing action fails, change your target picture.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speakers. Be sure you have made a correct connection to the projector audio input. See "Connection" on page 16 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight Audio Settings and press MODE/ENTER. The Audio Settings page displays.

3.Highlight Mute and press / to select On.

Adjusting the sound level

To adjust the sound level, press VOLUME+/VOLUME- on the remote control, or:

1.Repeat steps 1-2 above.

2.Press to highlight Volume and press / to select a desired sound level.

Adjusting the microphone volume

To adjust the microphone sound level, press MIC/VOL keys (+/-) on the remote control, or:

1.Repeat steps 1-2 above.

2.Press to highlight Microphone Volume and press / to select a desired sound level.

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.Repeat steps 1-2 above.

2.Press to highlight Power On/Off Ring Tone and press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

Operation 35

Image 35

Contents MX880UST Model Name MX712 UST Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Confined. Allow at least 50 cm clearance Inverted images for ceiling mount InstallationIntroduction Projector featuresShipping contents Projector exterior view Controls and functions Keystone/Arrow buttons / Up Down Remote controlTest AutoNumeric buttons Operating the Laser pointerMute MIC/VOL +Operating the projector from the front Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection Component Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceAbout the microphone input Playing sound through the projectorPage Starting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Highlight Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function If you forget the passwordEntering the password recall procedure Changing the passwordSwitching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageCreating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Advanced Network Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsColor Splash System Setup Advanced menu Function Description Panel KeyLock BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure the lamp cover Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsWall mount installation DimensionsSupported timing for PC input Timing chartTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users