BenQ MX880UST user manual Description of each menu

Page 54

Description of each menu

1. DISPLAY menu

Function

Description

Wall Color

Corrects the projected picture’s color when the projection surface is not

white. See "Using Wall Color" on page 29 for details.

 

 

 

Aspect Ratio

There are several options to set the image's aspect ratio depending on

your input signal source. See "Selecting the aspect ratio" on page 27 for

 

details.

 

 

Keystone

Corrects any keystoning of the image. See "Correcting keystone" on

page 22 for details.

 

 

 

 

Displays the position adjustment page. To move the projected image,

 

use the directional arrow keys. The values shown on the lower position

Position

of the page change with every key press you made until they reach their

maximum or minimum.

 

This function is only available when a PC signal (analog RGB) is

 

selected.

 

Adjusts the clock phase to reduce image

 

distortion.

Phase

 

 

This function is only available when a PC

 

signal (analog RGB) is selected.

H. Size

Adjusts the horizontal width of the image.

This function is only available when a PC signal (analog RGB) is

 

selected.

Digital Zoom

Magnifies or reduces the projected image. See "Magnifying and

searching for details" on page 27 for details.

 

 

 

 

This projector features a 3D function which enables you to enjoy the

 

3D movies, videos, and sporting events in a more realistic way by

 

presenting the depth of the images. You need to wear a pair of 3D

 

glasses to view the 3D images.

 

• For a PC type signal:

 

When the vertical frequency is 60Hz or 120Hz, and the content being

 

projected is made with 3D technology, selecting On will present the 3D

3D Sync

images.

• For a video type signal:

 

 

When the content being projected is made with 3D technology,

 

selecting On will present the 3D images.

 

When the 3D Sync function is On:

 

• The brightness level of the projected image will decrease.

 

• The Picture Mode cannot be adjusted.

 

• The Keystone can only be adjusted within limited degrees.

3D Sync

When you discover the inversion of the image depth, enable this

Invert

function to correct the problem.

 

 

54 Operation

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Digital Projector MX880UST Model Name MX712 USTTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Installation Inverted images for ceiling mountProjector features IntroductionShipping contents Projector exterior view Controls and functions Auto Remote controlTest Keystone/Arrow buttons / Up DownMIC/VOL + Operating the Laser pointerMute Numeric buttonsRemote control effective range Replacing the remote control batteriesOperating the projector from the front Front Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection Terminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good NormalPlaying sound through the projector About the microphone inputPage Operation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus HighlightSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERChanging the password If you forget the passwordEntering the password recall procedure Disabling the password functionSwitching input signal Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeLocking control keys Creating your own startup screenAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Direct power off Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Advanced Network Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground System Setup Advanced menu Function Description Panel KeyLock Color SplashBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Tighten the screws that secure the lamp coverLamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Wall mount installationTiming chart Supported timing for PC inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Copyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive
Top Page Image Contents