BenQ MX880UST user manual Using the menus, Highlight

Page 23

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

Below is the overview of the OSD menu.

Main menu icon

Main menu							DISPLAY
Main menu							DISPLAY
									Wall Color
									Aspect Ratio
									Keystone
Sub-menu									Position
									Position
									Phase



									H. Size


									Digital Zoom
									3D Sync
									3D Sync Invert
Highlight									Teaching Template


Current input signal									Analog RGB
									Analog RGB

Off

Auto

ENTER							Status
ENTER
0


0
On							Press MENU/
On
Disable
Disable
							EXIT to the
							previous
							page or to
MENU	Exit						exit.
MENU	Exit

The following example describes how to set the OSD language.

1.Press MENU/EXIT on the projector or remote control to turn the OSD menu on.

DISPLAY

Wall Color	Off
Aspect Ratio	Auto
Keystone
Position
Phase	0
H. Size	0
Digital Zoom
3D Sync	On
3D Sync Invert	Disable
Teaching Template
Analog RGB	MENU Exit

3.Press to highlight Language and press / to select a preferred language.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
MyScreen

Analog RGB

MENU Exit

2.Use / to highlight the SYSTEM SETUP: Basic menu.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
MyScreen

4.Press MENU/EXIT twice* on the projector or remote control to leave and save the settings.

*The first press leads you back to the main menu and the second press closes the OSD menu.

Analog RGB	MENU Exit

Operation 23

Image 23

Contents MX880UST Model Name MX712 UST Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Confined. Allow at least 50 cm clearance Inverted images for ceiling mount InstallationIntroduction Projector featuresShipping contents Projector exterior view Controls and functions Keystone/Arrow buttons / Up Down Remote controlTest AutoNumeric buttons Operating the Laser pointerMute MIC/VOL +Operating the projector from the front Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection Component Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceAbout the microphone input Playing sound through the projectorPage Starting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Highlight Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function If you forget the passwordEntering the password recall procedure Changing the passwordSwitching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageCreating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Advanced Network Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsColor Splash System Setup Advanced menu Function Description Panel KeyLock BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure the lamp cover Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsWall mount installation DimensionsSupported timing for PC input Timing chartTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users