BenQ MX880UST user manual Adjusting the projected image, Adjusting the projection angle

Page 21

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 2 adjuster feet. These adjusters change the image height and projection angle. To adjust the projector:

Screw the rear adjuster feet to fine-tune the horizontal angle.

To retract the foot, screw the rear adjuster feet in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 22 for details.

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

• The screen will be blank while AUTO is functioning.

•This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image clarity

Sharpen the image by rotating the focus ring.

Operation 21

Image 21

Contents MX880UST Model Name MX712 UST Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Inverted images for ceiling mount InstallationIntroduction Projector featuresShipping contents Projector exterior view Controls and functions Test Remote controlAuto Keystone/Arrow buttons / Up DownMute Operating the Laser pointerMIC/VOL + Numeric buttonsRemote control effective range Replacing the remote control batteriesOperating the projector from the front Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsConnection Connecting audio Connecting video source devicesTerminal name Terminal appearance Component Video Better Good NormalAbout the microphone input Playing sound through the projectorPage Starting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Highlight Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordChanging the password Disabling the password functionSwitching input signal Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageLocking control keys To activate the High Altitude ModeOperating in a high altitude environment Creating your own startup screenAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring ToneCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Advanced Network Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description TeachingTimer System Setup Basic menu Function Description Quick AutoSettings SearchLock System Setup Advanced menu Function Description Panel KeyBackground Color SplashReset All System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure the lamp cover Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsWall mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive