BenQ W1200 Optimizing the image, Selecting a picture mode, Setting the User 1/User 2/User 3 mode

Page 31

Optimizing the image

Selecting a picture mode

The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type.

To select an operation mode that suits your need, you can follow one of the following steps.

• Press MODE/ENTER on the remote control or projector repeatedly until your desired mode is selected.

•Go to the PICTURE: Basic > Picture Mode menu and press / to select a desired mode.

The picture modes are listed below.

1.Dynamic mode: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.

2.Standard mode: Is designed for presentations. The brightness is emphasized in this mode.

3.Cinema mode: Is appropriate for playing colorful movies, video clips from digital cameras or DVs through the PC input for best viewing in a blackened (little light) environment.

4.User 1/User 2/User 3 mode: Recalls the settings customized based on the current available picture modes. See "Setting the User 1/User 2/User 3 mode" on page 31 for details.

Setting the User 1/User 2/User 3 mode

There are two user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the User 1/User 2/User 3) as a starting point and customize the settings.

1.Press MENU/EXIT to open the On-Screen Display (OSD) menu.

2.Go to the PICTURE: Basic: Basic > Picture Mode menu.

3.Press / to select User 1/ User 2/User 3.

4.Press to highlight Reference Mode.

This function is only available when User 1/User 2/User 3 mode is selected up in the Picture Mode sub-menu item.

5.Press / to select a picture mode that is closest to your need.

6.Press to select a sub-menu item to be changed and adjust the value with / . See "Fine-tuning the image quality" below for details.

7.When all settings have been done, highlight Save Settings and press MODE/ENTER to store the settings.

8.The confirmation message 'Setting Saved' displays.

The User 1/User 2/User 3 functions can also be accessible by pressing

USER-1/USER-2/USER-3 on the remote control.

Operation 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents W1100/W1200 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Left Right Remote controlSize, PIP Pos, PIP Active Color II PowerTest Replacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection ConnectionConnection Video Normal Connecting Video source devicesStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordChanging the password Entering the password recall procedureDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsPicture Letter Box format picture Optimizing the image Selecting a picture modeSetting the User 1/User 2/User 3 mode Go to the Picture Basic Basic Picture Mode menuAdvanced picture quality controls Fine-tuning the image qualitySelecting a Gamma Selection Selecting a Color TemperatureFine-Tuning a Color Temperature Adjusting Brilliant Color3D Color Management Freezing the image Setting the Sleep TimerSelecting a Film Mode Hiding the imageTurning on/off the SRS Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentTurning on the Power on/off Ring Tone Adjusting the sound levelAdjusting the Treble level Adjusting the Bass levelVideo Shutting down the projector Personalizing the projector menu displayMenu system Menu operationAudio System Setup Description of each menu Picture ModeISF Source SRS Language Projector Position Menu Settings System Setup menu Information menu Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp Cover removed Resetting the lamp timer Indicators Troubleshooting Optical SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Patents for W1100/W1200 Warranty and Copyright informationFCC statement Regulation statementsRegulation statements Regulation statements
Top Page Image Contents