BenQ W1200 user manual Language Projector Position Menu Settings

Page 47

FUNCTION

Language

Projector

Position

Menu

Settings

5.
SYSTEMSETUP menu	Settings
	Operation

Standby

Settings

DESCRIPTION

Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 25 for details.

The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. See "Choosing a location" on page 15 for details.

Menu display time

Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu position

Sets the On-Screen Display (OSD) menu position.

Direct Power On

Selecting On enables the function. See "Starting up the projector" on page 22 for details.

Auto Power Off

Allows the projector to turn off automatically if no input signal is detected after a set period of time. See "Setting Auto Power Off" on page 50 for details.

Blank Timer

Sets the image blank time when the Blank feature is activated, once elapsed the image will return to the screen. See "Hiding the image" on page 35for details.

Sleep Timer

Sets the auto-shutdown timer. The timer can be set to a value between 30 minutes and 12 hours.

Background Color

Allows you to select which background color will display when no signal is input into the projector. Three options are available: Black, Blue, or Purple.

Splash Screen

Allows you to select which logo screen will display during projector start-up. Three options are available: BenQ logo, Black screen, or Blue screen.

Monitor Out

Selecting On enables the function. The projector can output a VGA

signal when it is in standby mode and the COMPUTER jack is correctly connected to devices.

Enabling this function slightly increases the standby power consumption.

Operation 47

Image 47

Contents W1100/W1200 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Size, PIP Pos, PIP Active Remote controlLeft Right Test II PowerColor Replacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection ConnectionConnection Video Normal Connecting Video source devicesStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsPicture Letter Box format picture Optimizing the image Selecting a picture modeSetting the User 1/User 2/User 3 mode Go to the Picture Basic Basic Picture Mode menuAdvanced picture quality controls Fine-tuning the image qualitySelecting a Gamma Selection Selecting a Color TemperatureFine-Tuning a Color Temperature Adjusting Brilliant Color3D Color Management Freezing the image Setting the Sleep TimerSelecting a Film Mode Hiding the imageTurning on/off the SRS Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentTurning on the Power on/off Ring Tone Adjusting the sound levelAdjusting the Treble level Adjusting the Bass levelVideo Shutting down the projector Personalizing the projector menu displayMenu system Menu operationAudio System Setup Description of each menu Picture Mode ISF Source SRS Language Projector Position Menu Settings System Setup menu Information menu Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp Cover removed Resetting the lamp timer Indicators Troubleshooting Optical SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Patents for W1100/W1200 Warranty and Copyright informationFCC statement Regulation statementsRegulation statements Regulation statements