BenQ W1060 user manual Description of each menu, Picture Mode

Page 47

Description of each menu

 

FUNCTION

DESCRIPTION

 

 

 

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

 

projector image set-up to suit your program type. See "Selecting a

 

 

picture mode" on page 35 for details.

 

 

 

 

Reference

Selects a picture mode that most suits your need for the image quality

 

and further fine-tune the image based on the selections listed on the

 

Mode

 

same page below.

 

 

 

 

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on

 

page 36 for details.

 

 

 

 

 

1.

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 36 for details.

PICTURE:

 

 

 

 

Adjusts the color saturation level -- the amount of each color in a

 

 

 

Color

video image. See "Adjusting Color" on page 36 for details.

 

This function is only available when Video or S-Video with NTSC

 

 

 

 

system is selected.

Basic

 

 

 

Adjusts the red and green color tones of the image. See "Adjusting

Tint

Tint" on page 36 for details.

 

 

This function is only available when Video or S-Video with NTSC

menu

 

 

system is selected.

 

 

 

Adjusts the image to make it look sharper or softer. See "Adjusting

 

 

 

Sharpness

Sharpness" on page 36 for details.

 

This function is only available when Video or S-Video with NTSC

 

 

 

 

system is selected.

 

 

 

 

Flesh Tone

See "Adjusting Flesh Tone" on page 36 for details.

 

 

 

 

Save Settings

Saves the settings made for User 1 or User 2 or User 3 mode.

 

 

 

 

Reset Picture

Resets the picture settings for User 1 or User 2 or User 3 mode.

 

Settings

 

English

Operation 47

Image 47
Contents W1060 Digital Projector WelcomeTable of contents Important safety instructions English Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side FOCUS/ZOOM Ring Power indicator lightRemote control Tint 19. PCDown cursor/Keystone AutoRemote control effective range Replacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size English Diagonal W1060 projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionsBetter video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesTo connect the projector to an Audio source device Connecting Component Video source devicesTo connect the projector to a Component Video source device To connect the projector to an S-Video source device Connecting S-Video source devicesTo connect the projector to a composite Video source device Connecting Composite Video source devicesStarting up the projector OperationSecuring the projector Using the menusUsing a security cable lock If you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Keystone function Fine-tuning the image size and clarityUsing Auto Keystone Correcting keystoneSelecting Color Space Conversion Magnifying and searching for detailsSelecting the aspect ratio Letter Box About the aspect ratioReal Optimizing the image Selecting a picture modeSetting the User 1/User 2/User 3 mode Go to the Picture Basic Picture Mode menuFine-tuning the image quality in user modes About color temperatures Adjusting Clarity ControlSelecting a Color Temperature Selecting a Color Temperature Fine TuningSelecting a White Peaking Adjusting Brilliant ColorSelecting a White Balance Selecting a Gamma SelectionSelecting a Video Format Hiding the image Setting the Sleep TimerSelecting a Film Mode Setup Basic Operation SettingsOperating in a high altitude environment Setup Basic Remote Receiver menuRemote Receiver Freezing the imageMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power on/off Ring ToneShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Tion Description of each menu Picture ModePicture Advanced Display menu Sleep Timer Direct Power OnAuto Power Off Blank TimerReset Lamp Timer VolumePower On/Off Ring Tone Lamp ModeColor System Picture ModeResolution SourceCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp cover removedEnsure the handle is fully laid flat and locked in place Resetting the lamp timer Indicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for PC input Timing chartSupported timing for Component-YPbPr input Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputsSXGA60 Disclaimer Warranty and Copyright informationLimited warranty Copyright