BenQ W1060 user manual Troubleshooting

Page 59

Troubleshooting

The projector does not turn on.

Cause

Remedy

 

 

There is no power from the power

Plug the power cord into the AC inlet on the

projector, and plug the power cord into the

cable.

power outlet. If the power outlet has a switch,

 

make sure that it is switched on.

 

 

Attempting to turn the projector on

Wait until the cooling down process has

again during the cooling process.

completed.

 

 

No picture

Cause

Remedy

 

 

The video source is not turned on or

Turn the video source on and check that the

connected correctly.

signal cable is connected correctly.

 

 

The projector is not correctly

Check the connection.

connected to the input signal device.

 

 

 

The input signal has not been

Select the correct input signal with the

SOURCE key on the projector or remote

correctly selected.

control.

 

 

 

Blurred image

Cause

Remedy

 

 

The projection lens is not correctly

Adjust the focus of the lens using the focus

focused.

ring.

 

 

The projector and the screen are not

Adjust the projection angle and direction as

aligned properly.

well as the height of the unit if necessary.

 

 

Remote control does not work

Cause

Remedy

 

 

The battery is out of power.

Replace the battery with new one.

There is an obstacle between the

Remove the obstacle.

remote control and the projector.

 

 

 

You are too far away from the

Stand within 7 meters (23 feet) of the

projector.

projector.

 

 

The password is incorrect

Cause

Remedy

 

 

You do not remember the password.

Please see "Entering the password recall

procedure" on page 28 for details.

 

 

 

English

Troubleshooting 59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents W1060 Digital Projector WelcomeTable of contents Important safety instructions English Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side FOCUS/ZOOM Ring Power indicator lightRemote control Tint 19. PCDown cursor/Keystone AutoRemote control effective range Replacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size English Diagonal W1060 projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionsBetter video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesTo connect the projector to an Audio source device Connecting Component Video source devicesTo connect the projector to a Component Video source device To connect the projector to an S-Video source device Connecting S-Video source devicesTo connect the projector to a composite Video source device Connecting Composite Video source devicesStarting up the projector OperationSecuring the projector Using the menusUsing a security cable lock If you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Keystone function Fine-tuning the image size and clarityUsing Auto Keystone Correcting keystoneSelecting Color Space Conversion Magnifying and searching for detailsSelecting the aspect ratio Letter Box About the aspect ratioReal Optimizing the image Selecting a picture modeSetting the User 1/User 2/User 3 mode Go to the Picture Basic Picture Mode menuFine-tuning the image quality in user modes About color temperatures Adjusting Clarity ControlSelecting a Color Temperature Selecting a Color Temperature Fine TuningSelecting a White Peaking Adjusting Brilliant ColorSelecting a White Balance Selecting a Gamma SelectionSelecting a Video Format Hiding the image Setting the Sleep TimerSelecting a Film Mode Setup Basic Operation SettingsOperating in a high altitude environment Setup Basic Remote Receiver menuRemote Receiver Freezing the imageMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power on/off Ring ToneShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Tion Description of each menu Picture ModePicture Advanced Display menu Sleep Timer Direct Power OnAuto Power Off Blank TimerReset Lamp Timer VolumePower On/Off Ring Tone Lamp ModeColor System Picture ModeResolution SourceCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp cover removed Ensure the handle is fully laid flat and locked in place Resetting the lamp timer Indicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for PC input Timing chartSupported timing for Component-YPbPr input Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputsSXGA60 Disclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents