BenQ W1060 user manual Connecting S-Video source devices

Page 23

Connecting S-Video source devices

Examine your Video source device to determine if it has an unused S-Video output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1.Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2.Connect the other end of the S-Video cable to the S-VIDEOsocket on the projector.

To connect the projector to an Audio source device:

1.Take a suitable audio cable and connect one end to the AUDIO OUT jack of the AV

device. Connect the other end of the cable to the AUDIO IN jack on the projector. Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Adjusting the sound" on page 42 for details.

The final connection path should be like that shown in the following diagram:

S-Video Cable

AV device

		COMPUTER
COMPONENT	S-VIDEO	VIDEO	PC	HDMI-1	HDMI-2
	USB	RS-232
	USB
		AUDIO	L	AUDIO R
		OUT	IN

Audio Cable

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 20 for details.

English

Connections 23

Image 23

Contents W1060 Digital Projector WelcomeTable of contents Important safety instructions English Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side FOCUS/ZOOM Ring Power indicator lightRemote control Tint 19. PCDown cursor/Keystone AutoRemote control effective range Replacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size English Diagonal W1060 projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionsBetter video quality Connecting Video source devicesConnecting Audio Best video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesTo connect the projector to an Audio source device Connecting Component Video source devicesTo connect the projector to a Component Video source device To connect the projector to an S-Video source device Connecting S-Video source devicesTo connect the projector to a composite Video source device Connecting Composite Video source devicesStarting up the projector OperationSecuring the projector Using the menusUsing a security cable lock If you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Keystone function Fine-tuning the image size and clarityUsing Auto Keystone Correcting keystoneSelecting Color Space Conversion Magnifying and searching for detailsSelecting the aspect ratio Letter Box About the aspect ratioReal Optimizing the image Selecting a picture modeSetting the User 1/User 2/User 3 mode Go to the Picture Basic Picture Mode menuFine-tuning the image quality in user modes About color temperatures Adjusting Clarity ControlSelecting a Color Temperature Selecting a Color Temperature Fine TuningSelecting a White Peaking Adjusting Brilliant ColorSelecting a White Balance Selecting a Gamma SelectionSelecting a Video Format Hiding the image Setting the Sleep TimerSelecting a Film Mode Setup Basic Operation SettingsOperating in a high altitude environment Setup Basic Remote Receiver menuRemote Receiver Freezing the imageMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power on/off Ring ToneShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Tion Description of each menu Picture ModePicture Advanced Display menu Sleep Timer Direct Power OnAuto Power Off Blank TimerReset Lamp Timer VolumePower On/Off Ring Tone Lamp ModeColor System Picture ModeResolution SourceCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp cover removedEnsure the handle is fully laid flat and locked in place Resetting the lamp timer Indicators Troubleshooting Projector specifications SpecificationsDimensions Supported timing for PC input Timing chartSupported timing for Component-YPbPr input Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputsSXGA60 Disclaimer Warranty and Copyright informationLimited warranty Copyright