BenQ PB9200 user manual Operating, Selecting An Input Signal

Page 21

PB9200-e.book Page 15 Thursday, May 27, 2004 2:15 PM

Operating

Selecting An Input Signal

1.Select an input signal.

■ Using the INPUT dial

Turn the INPUT dial of the projector. Turning the dial cycles through the input ports as shown below. Select the signal you wish to project.

M1-D RGB BNC

VIDEO S-VIDEO COMPONENT

■Using SEARCH button

Press the SEARCH button of the projector or the remote control.

Pressing the button automatically cycles through input ports and displays the picture of retrieved signal.

memo If no signal is found or the projector is unstable to find an input signal at any of its ports, it will turn to the state it was in prior to the search.

M1-D RGB BNC

VIDEO S-VIDEO COMPONENT

■Using RGB button

Press the RGB button of the remote control. Pressing the button toggles between the RGB ports as shown below Select the signal you wish to project.

SEARCH button

KEYSTONE

M1-D SEARCH

RGB INPUT

BNC	RESET

COMPONENT ENTER

S-VIDEO	MENU

INPUT dial

					VIDEO button
STANDBY/ON				RGB	RGB button
LASER INDICATOR
+		+		+
LENS SHIFT	FOCUS			ZOOM
–		–		–
BLANK	ASPECT			LASER
PREVIOUS				NEXT
	MOUSE
ESC	MENU				SEARCH button
POSITION	RESET			AUTO	SEARCH button
MAGNFY	PinP			VOLUME
ON
	FREEZE			MUTE
OFF
	KEYSTONE SEARCH
	1	2	3
ID CHANGE

M1-D RGB BNC

■Using VIDEO button

Press the VIDEO button of the remote control. Pressing the button toggles between the VIDEO ports as shown below Select the signal you wish to project.

COMPONENT S-VIDEO VIDEO

2.Use the FOCUS buttons to adjust the focus.

3.Use the ZOOM buttons to adjust the screen size.

ZOOMFOCUS

FOCUS ZOOM

buttons button

Operating 15

Image 21

Contents Welcome Copyright Table of Contents Iv Table of Contents Multifunctional SettingsTable of Contents TroubleshootingVi Table of Contents Quick correction of distorted images electrically Projector FeaturesPreparation PreparationPart Names ProjectorProjector Rear/Left Remote Control Remote ControlControl Buttons Mouse left buttonArrangement Setting UpReference for the 43 aspect ratio Reference for the 169 aspect ratioUsing The Lens Shift Buttons Adjusting The Projectors ElevatorConnecting Your Devices If using a M1-D input to mouse control If using a BNC inputComputerProjector If using a component signal If using a s-video signalIf using a Scart RGB input VCR/DVD Player ProjectorMonitor Projector Connecting The Power SupplySpeaker Projector RGB OUTRemote Control About The Laser PointerPutting Batteries Meters with a 60 degree range Degrees to the left Operating The Remote ControlUsing The Remote ID Feature Using The Mouse/Keyboard Control FunctionID Change switch Power ON/OFF Turning On The PowerTurning Off The Power Operating Selecting An Input SignalSelecting The Aspect Ratio Using The Automatic Adjustment FeatureAdjusting The Picture Position Correcting The Keystone DistortionPress the Keystone button Press the Mute or Volume button to restore the sound Adjusting The VolumeMuting The Sound Temporarily Blanking The ScreenFreezing The Screen Using The Magnify FeatureSelecting An Audio Input Displaying The Child WindowUsing The Menu Functions Multifunctional SettingsEx. Turning off the built-in speaker EnterMain Menu Gamma PICTURE-1 MenuSharpness ColorMY Memory PICTURE-2 Menu PhasePosition SizeInput Menu P. Input PowerupP. Posit InputAdjust Power OFFAuto Menu Video Component SearchBlank Screen MenuStart UP LockWorks Message of the Auto in Progress for the auto adjust How to register your picture as the MyScreenTial setting MessageOption Menu Fanspee ServiceAuto LensSetup Network MenuDhcp Network Setting Up When your Network enables the Dhcp functionEx. Case of IP Address = For more information, call your dealer LampReplacing The Lamp Case of replacement by yourselfScrews LampCaring For The Air Filter Air FilterOther Care Caring For The Cabinet And Remote ControlCaring For The Inside Of The Projector Caring For The LensRelated Messages TroubleshootingThere is no input signal Internal portion temperature is risingInputted signal is outside of the response Message DescriptionStandby Lamp Temp Regarding The Indicator LampsCooling fan is not operating Description IndicatorBecome heated Become overcooledInput changeover settings are mismatched Power switch is not set to the on positionPhenomena That May Easily Be Mistaken For Machine Defects These has not been properly fixedSound is muted Color settings are not correctly adjustedWindow is displayed Lens cap is attachedWarranty And After-Service Warranty And After-ServiceSpecification SpecificationsRGB input ports Video input ports