Onkyo HT-R590 instruction manual Error Messages, Changing the Speaker Setup Manually

Page 26

Error Messages

While Audyssey 2EQ® Room Correction and Speaker Setup is in progress, one of the error messages below may appear.

2EQ: Auto Setup

Audyssey

Ambient noise is too high. Error message

Retry

Cancel

The options are:

`Retry:

Try again.

`Cancel:

Cancel Audyssey 2EQ Room Correction and Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of the noise and try again.

• Speaker matching error!

The number of speakers detected was different from that of the first measurement. Check the speaker connection.

• Writing Error!

This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No” means that no speaker was detected.

Tip

•See “Speaker Configuration” for appropriate settings (➔ page 12).

Changing the Speaker Setup Manually

You can manually make changes to the settings found during Audyssey 2EQ Room Correction and Speaker Setup.

See also:

•“Sp Config (Speaker Configuration)” (➔ page 36)

•“Sp Distance (Speaker Distance)” (➔ page 37)

•“Level Cal (Level Calibration)” (➔ page 37)

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey 2EQ Room Correction and Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker Configuration” screen as “No”, increase the subwoofer’s volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer’s instruction manual for details.

En

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents HT-R590 Attain an abnormal high temperature Local regulations when disposing of batteriesTemperature protection operates if the apparatus 10 cm 4 at the rear. The rear edge of the shelf orPrecautions Installing the batteries Supplied AccessoriesMake sure you have the following accessories Aiming the remote controllerContents Processing FeaturesAmplifier MiscellaneousFront & Rear Panels Front PanelDisplay For detailed information, see the pages in parenthesesRemote Control jack Rear PanelRemote MODE/INPUT Selector buttons 19, 47 to Remote ControllerControlling the AV Receiver Controlling the tunerConnecting the Speaker Cables Connecting the AV ReceiverConnecting Your Speakers Screw-type speaker terminalsUsing a Powered Subwoofer Speaker ConfigurationSpeaker Connection Precautions Number of channelsAV Cables and Jacks About AV ConnectionsConnected image with AV components Hdmi cableJack Components Assignable Connecting Components with HdmiAudio return channel ARC function See Recording to make a connection for video recording Connecting Your ComponentsHow to record the video System On/Auto Power On Connecting Onkyo uComponentsConnecting a Recording Component Remote ControlConnecting Antenna Connecting the Power CordTurning On See Auto Standby about a power management settingTurning On/Off the AV Receiver Turning OffPlaying the Connected Component Controlling Contents of USB DevicesPlayback Playing iPod/iPhone via USB Standard Mode controlUnderstanding Icons on the Display ModeTuning into Radio Stations Extended Mode controlUsing the Tuner Playing USB DevicePresetting AM/FM Stations Using RDS Asian modelsListening to Traffic News TP Displaying Radio Text RTFinding Stations by Type PTY Measurement procedure Using Basic FunctionsUsing the Automatic Speaker Setup CalibrationWhen you’ve finished making the settings, press Set the speaker setup microphone at the MainListening Position a, and connect it to the Setup MIC jack ` CancelError Messages Changing the Speaker Setup ManuallyAbout Listening Modes Using the Listening ModesSelecting Listening Modes Speaker Layout Following audio formats are supported by the listening modeInput Source Onkyo-Original DSP Listening ModesListening Modes Listening modes cannot be selected with some source formats Using the Home Menu Using the Sleep TimerDisplaying Source Information Setting the Display BrightnessUsing the Music Optimizer Changing the Input DisplayRecording Using HeadphonesMuting the AV Receiver AV RecordingCommon Procedures in Setup Menu Advanced SetupOn-screen Setup Menus Explanatory NotesComponent Component Video Input Input selector Default assignmentHdmi Input Digital Audio Digital Audio InputSurround Back Ch Sp Config Speaker ConfigurationFront Crossover Crossover FrequencySp Distance Speaker Distance Audio AdjustMultiplex/Mono Settings Level Cal Level CalibrationTheater-Dimensional Setting Dolby SettingsDTS Setting Source Setup AudysseyAudio Selector Preset Name For Input SelectorSync Hardware Hdmi Through Hdmi SetupHdmi Ctrl Rihd Audio TV OutSpeaker Levels Using the Audio SettingsTone Control Settings CinemaFILTER Late Night FunctionMusic Optimizer Controlling Your iPod/iPhone Using the Onkyo DockIPod/iPhone Playback via Onkyo Dock Available buttons Remote Control Codes for Onkyo Components Connected via u Preprogrammed Remote Control CodesEntering Remote Control Codes Controlling Other Onkyo ComponentsControlling Other Components Resetting Remote Mode ButtonsResetting the Remote Controller Controlling a Blu-ray Disc/DVD Player, HD DVD PlayerDisc + Components Buttons DVDplayerCassettetape deck AV receiver turns off unexpectedly TroubleshootingCan’t turn on the AV receiver There’s no sound, or it’s very quietAbout DTS signals There’s no sound with a certain signal formatSpeaker volume cannot be set as required Only the front speakers produce soundStandby power consumption Remote controller doesn’t workCan’t access the music files on a USB device Sound changes when I connect my headphonesUfunctions don’t work Video Attoff defaultHow do I change the language of a multiplex source Video AttenuationAudio Connection Formats Connection Tips and Video Signal PathVideo Connection Formats Supported Audio File Formats USB FeaturesUSB Device Requirements About Copyright Protection About HdmiSupported Audio Formats Operations that can be performed with Connection Using an RIHD-compatible TV, Player, or RecorderAbout p-compatible components Confirm the settings How to connect and setupConfirm the connecting and setting Operate with the remote controllerVideo Section SpecificationsAmplifier Section Tuner SectionOnkyo Europe Electronics GmbH Onkyo Europe Electronics GmbH UK Branch
Related manuals
Manual 60 pages 12.76 Kb

HT-R590 specifications

The Onkyo HT-R590 is a versatile and feature-rich home theater receiver that has garnered attention for its impressive audio performance and user-friendly design. This device serves as the heart of a home entertainment system, delivering a dynamic audio experience that enhances movies, music, and gaming.

One of the standout features of the HT-R590 is its support for high-definition audio formats. The receiver is capable of decoding Dolby TrueHD and DTS-HD Master Audio, making it an excellent choice for those who appreciate high-quality sound in their media. With a powerful output of 100 watts per channel, it can drive even the most demanding speakers, ensuring that soundtracks and effects come to life with clarity and depth.

The HT-R590 also features a variety of connectivity options, including multiple HDMI inputs that support 4K video pass-through. This means that users can connect their Blu-ray players, gaming consoles, and streaming devices without hassle, making it easy to create a comprehensive home theater setup. The receiver also includes legacy connections for older devices, such as composite and component video inputs, providing flexibility for various audio and video sources.

Another notable characteristic of the Onkyo HT-R590 is its incorporation of Audyssey technology. This advanced room correction technology optimizes the sound output based on the specific acoustics of the room. By analyzing the space and adjusting the audio settings accordingly, users can achieve a balanced and immersive sound experience, regardless of room dimensions or speaker placements.

The user interface of the HT-R590 is designed with convenience in mind. A clear and intuitive remote control allows users to navigate settings, adjust audio levels, and switch inputs with ease. Furthermore, the on-screen display simplifies the setup process, guiding users through configuration steps to ensure optimal performance.

In addition to its robust audio capabilities, the Onkyo HT-R590 supports various streaming options through built-in Bluetooth technology. This allows users to easily connect their smartphones and tablets to stream music directly to the receiver, expanding the functionality beyond traditional home theater setups.

In summary, the Onkyo HT-R590 is an excellent choice for anyone looking to elevate their home audio experience. With its high-definition audio support, extensive connectivity options, advanced room correction technology, and user-friendly interface, this receiver stands out as a formidable option in the home theater market, delivering exceptional sound quality and versatility for a wide range of multimedia applications.
Top Page Image Contents