Onkyo HT-R590 Only the front speakers produce sound, Only the center speaker produces sound

■Only the front speakers produce sound

When the Stereo or Mono listening mode is selected,	29
only the front speakers and subwoofer produce
sound.
Check the Speaker Configuration.	36

■Only the center speaker produces sound

If you use the Dolby Pro Logic IIx Movie, Dolby Pro — Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.

Make sure the speakers are configured correctly. 36

■The surround speakers produce no sound

When the T-D (Theater-Dimensional), Stereo or	29
Mono listening mode is selected, the surround
speakers produce no sound.
Depending on the source and current listening mode,	27–28
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
Make sure the speakers are configured correctly.	36

■The center speaker produces no sound

When the Stereo or Mono listening mode is selected,	29
the center speaker produces no sound.
Make sure the speakers are configured correctly.	36

■The front high or surround back speakers produce no sound

Depending on the current listening mode, no sound 27–28may be produced by the front high or surround back speakers. Select another listening mode.

Not much sound may be produced by the front high — or surround back speakers with some sources.

Make sure the speakers are configured correctly. 36

■The subwoofer produces no sound

When you play source material that contains no	—
information in the LFE channel, the subwoofer
produces no sound.
Make sure the speakers are configured correctly.	36

■There’s no sound with a certain signal format

Check the digital audio output setting on the	—
connected device. On some game consoles, such as
those that support DVD, the default setting is off.
With some DVD-Video discs, you need to select an	—
audio output format from a menu.
Depending on the input signal, some listening modes	27–28
cannot be selected.

■ Can’t get 6.1/7.1 playback

If no surround back speakers or front high speakers	—
are connected, 6.1/7.1 playback is not possible.
You can not always select all of the listening modes,	27–28
depending on the number of the speakers connected.

■The speaker volume cannot be set as required

Check to see if a maximum volume has been set.	19
If the volume level of each individual speaker has	24, 37

been adjusted to high positive values, then the maxi- mum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey 2EQ® Room Cor- rection and Speaker Setup has been completed.

■Noise can be heard

Using cable ties to bundle audio cables with power — cords, speaker cables, and so on may degrade the audio performance, so don’t do it.

An audio cable may be picking up interference. Try — repositioning your cables.

■The Late Night function doesn’t work

Make sure the source material is Dolby Digital,	44
Dolby Digital Plus, or Dolby TrueHD.

■ About DTS signals

When DTS program material ends and the DTS	—
bitstream stops, the AV receiver remains in DTS
listening mode and the DTS indicator remains on.
This is to prevent noise when you use the pause, fast
forward, or fast reverse function on your player. If
you switch your player from DTS to PCM, because
the AV receiver does not switch formats
immediately, you may not hear any sound, in which
case you should stop your player for about three
seconds, and then resume playback.

With some CD and LD players, you won’t be able to — playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

When playing DTS program material, using the	—
pause, fast forward, or fast reverse function on your
player may produce a short audible noise. This is not

amalfunction.

■The beginning of audio received by an HDMI IN can’t be heard

Since it takes longer to identify the format of an	—
HDMI signal than it does for other digital audio
signals, audio output may not start immediately.

Video

■ There’s no picture

Make sure that all video connecting plugs are pushed	13
in all the way.
Make sure that each video component is properly	14, 16
connected.
If the video source is connected to a component	15, 35
video input, you must assign that input to an input
selector, and your TV must be connected to
COMPONENT VIDEO OUT.
If the video source is connected to a composite video	15
input, your TV must be connected to the		En
corresponding composite video output.

51