3M X66 manual Image Menu, For a computer signal, For no signal, Over Scan, Position

Page 29

IMAGE Menu

IMAGE Menu

From the IMAGE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item

Description

 

 

 

Using the ▲/▼ buttons switches the mode for aspect ratio.

 

For a computer signal

 

NORMAL ó 4:3 ó 16:9 ó SMALL

ASPECT

For a video signal, s-video signal or component video signal

4:3 ó 16:9 ó 14:9 ó SMALL

 

For no signal

 

4:3 (fixed)

 

• This item can be selected only for a proper signal.

 

• NORMAL mode keeps the original aspect ratio setting.

 

Using the ▲/▼ buttons adjusts the over-scan ratio.

OVER SCAN

Large (It reduces picture) ó Small (It magnifies picture)

• This item can be selected only for a video, s-video and component video signal.

 

• When this adjustment is too large, certain degradation may appear

 

at the frame area of the picture. In such a case, please adjust small.

 

Using the ▲/▼ buttons adjusts the vertical position.

 

Up ó Down

 

• Over-adjusting the vertical position may cause noise to appear on the

 

screen. If this occurs please reset the vertical position to the default setting.

V POSITION

Pressing RESET button when V POSITION is selected will reset V

POSITION to the default setting.

 

 

• When this function is performed on a video signal, s-video signal, or

 

component video signal, the range of this adjustment depends on OVER

 

SCAN (above) setting. It is not possible to adjust when OVER SCAN is

 

set to 10.

 

Using the ▲/▼ buttons adjusts the horizontal position.

 

Left ó Right

 

• Over-adjusting the horizontal position may cause noise to appear on the

 

screen. If this occurs please reset the horizontal position to the default setting.

H POSITION

Pressing RESET button when H POSITION is selected will reset H

POSITION to the default setting.

 

 

• When this function is performed on a video signal, s-video signal, or

 

component video signal, the range of this adjustment depends on OVER

 

SCAN (above) setting. It is not possible to adjust when OVER SCAN is

 

set to 10.

(continued on next page)

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Fastening the lens cover Contents of packageHOT Part namesProjector Component Control panelRear panel Remote control On a horizontal surface Suspended from the ceiling Setting upArrangement Arrangement Setting up Monitor Connecting your devicesSpeakers VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesUsing the security bar and slot Connecting power supplyPutting batteries Remote controlAbout the remote control signal Using as a simple PC mouse & keyboard Changing the frequency of remote control signalMouse right button Press Reset button Mouse left button Press Enter buttonTurning off the power Power on/offTurning on the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal For a computer signal  For no signalAdjusting the zoom and focus Adjusting the projectors elevatorAdjusting the position Using the automatic adjustment featureAuto PositionCorrecting the keystone distortions Using the magnify featureKeystone Magnify ON/OFFTemporarily blanking the screen Freezing the screenFreeze BlankEasy Menu Using the menu functionAdvanced Menu Using the menu functionAspect Picture ModeAuto KeystoneEasy Menu Color Temp Picture MenuGamma LOAD-1, LOAD-2, LOAD-3, LOAD-4 Picture MenuMY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4For adjusting Gamma To adjust Custom function in Gamma and Color TempFor adjusting Color Temp Gamma Color TempFor no signal For a computer signalImage Menu Over ScanAuto Adjust PhaseImage Menu SizeProgressive Input MenuVideo NR Color SpaceVideo Format Input MenuFrame Lock ComputerStandard ResolutionCustom Standard CustomSetup Menu Volume Setup MenuSpeaker AudioBlank Screen MenuStart UP Screen MenuMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message No Input is DetectedSync is OUT of Range Auto on Option MenuAuto Search Lamp Time Option MenuAuto OFF FAN Speed ServiceMY Button Filter Message GhostKEY Lock Factory ResetRemote Freq InformationInputting the Password Using Security FeaturesChanging the Password SecurityIf you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off If you have forgotten your PIN Code Description SecurityTurning Off the PIN Lock Function Turning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off Type number Replacing the lamp MaintenanceLamp Lamp Lamp warningType number Cleaning the air filterAir filter Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Shutting the projector down Resetting all settingsSignal cables are not correctly connected Electrical power cord is not pluggedSignal source does not correctly work Input changeover settings are mismatchedColor Space setting is not suitable Color settings are not correctly adjustedNot properly adjusted Play monitorSpecification SpecificationsSpecification  SpecificationsIntended Use
Related manuals
Manual 2 pages 52.39 Kb
Top Page Image Contents