3M X66 manual Option Menu, Auto Search, Auto on

Page 40

OPTION Menu

OPTION Menu

From the OPTION menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.

Item

Description

	Using the ▲/▼ buttons turns on/off the automatic signal search function.
	TURN ON  TURN OFF
	When the TURN ON is selected, detecting no signal automatically
	cycles through input ports in the following order. The search is
AUTO SEARCH	started from the current port. Then when an input is found, the
	projector will stop searching and display the image.
	COMPUTER IN1  COMPUTER IN2
	VIDEO  S-VIDEO  COMPONENT

	Using the ▲/▼ buttons turns on/off the automatic keystone function.
	TURN ON  TURN OFF

		TURN ON : Automatic keystone distortion correction will be
		executed whenever changing the slant of the projector.
	AUTO	TURN OFF : This function is disabled. Please execute the AUTO
	KEYSTONE	KEYSTONE EXECUTE in the SETUP Menu for automatic
	KEYSTONE	keystone distortion correction.
		keystone distortion correction.

•When the projector is suspended from the ceiling this feature will not function properly so select the TURN OFF.

•This function will be unavailable when the Transition Detector is on (49).

	Using the ▲/▼ buttons turns on/off the AUTO ON function.
	TURN ON  TURN OFF
	When set to the TURN ON, the lamp in projector will be
	automatically turned on without the usual procedure (15), only
AUTO ON	when the projector is supplied with the power after the power was
AUTO ON	cut while the lamp was on.

•This function does not work as long as the power has been supplied to the projector while the lamp is off.

•After turning the lamp on by the AUTO ON function, if neither input nor operation is detected for about 30 minutes, the projector is turned off, even though the AUTO OFF function (41) is disabled.

(continued on next page)

40

Image 40

Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content Contents of package Fastening the lens coverProjector Part namesHOT Rear panel Control panelComponent Remote control Arrangement Setting upOn a horizontal surface Suspended from the ceiling Arrangement Setting up Connecting your devices MonitorSpeakers VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Using the security bar and slotAbout the remote control signal Remote controlPutting batteries Changing the frequency of remote control signal Using as a simple PC mouse & keyboardMouse right button Press Reset button Mouse left button Press Enter buttonTurning on the power Power on/offTurning off the power Adjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Selecting an input signal For a computer signal  For no signalAdjusting the projectors elevator Adjusting the zoom and focusUsing the automatic adjustment feature Adjusting the positionAuto PositionUsing the magnify feature Correcting the keystone distortionsKeystone Magnify ON/OFFFreezing the screen Temporarily blanking the screenFreeze BlankUsing the menu function Easy MenuUsing the menu function Advanced MenuPicture Mode AspectAuto KeystoneEasy Menu Gamma Picture MenuColor Temp Picture Menu LOAD-1, LOAD-2, LOAD-3, LOAD-4MY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4To adjust Custom function in Gamma and Color Temp For adjusting GammaFor adjusting Color Temp Gamma Color TempFor a computer signal For no signalImage Menu Over ScanPhase Auto AdjustImage Menu SizeInput Menu ProgressiveVideo NR Color SpaceInput Menu Video FormatFrame Lock ComputerResolution StandardCustom Standard CustomSetup Menu Setup Menu VolumeSpeaker AudioScreen Menu BlankScreen Menu Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Sync is OUT of Range No Input is DetectedMessage Auto Search Option MenuAuto on Auto OFF Option MenuLamp Time MY Button ServiceFAN Speed Ghost Filter MessageFactory Reset KEY LockRemote Freq InformationUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function If you have forgotten your PasswordTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code Turning Off the PIN Lock Function Description SecurityIf you have forgotten your PIN Code Setting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Lamp MaintenanceType number Replacing the lamp Lamp warning LampAir filter Cleaning the air filterType number Page Troubleshooting There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Resetting all settings Shutting the projector downElectrical power cord is not plugged Signal cables are not correctly connectedSignal source does not correctly work Input changeover settings are mismatchedColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Play monitorSpecification SpecificationsSpecification Specifications Intended Use

Related manuals

Manual 2 pages 52.39 Kb