3M X66 manual Electrical power cord is not plugged, These has not been properly fixed

Page 58

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it according to the following table.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The electrical power cord is not plugged in.

12

 

Correctly connect the power cord.

 

 

 

The main power source has been interrupted during

 

 

operation such as by a power outage (blackout), etc.

12, 15

 

Please disconnect the power plug from the power outlet,

Power does not

and allow the projector to cool down at least 10 minutes,

 

then turn the power on again.

 

come on.

 

 

Either there is no lamp and/or lamp door, or either of

 

 

 

 

these has not been properly fixed.

 

 

Please turn the power off and disconnect the power plug from

51, 52

 

the power outlet, and allow the projector to cool down at least

 

45 minutes. After the projector has sufficiently cooled down,

 

 

please make confirmation of the attachment state of the lamp

 

 

and lamp door, and then turn the power on again.

 

 

The signal cables are not correctly connected.

10

 

Correctly connect the connection cables.

 

 

Neither sounds

Signal source does not correctly work.

 

nor pictures are

Correctly set up the signal source device by referring to the

–

outputted.

manual of the source device.

 

 

The input changeover settings are mismatched.

16, 17

 

Select the input signal, and correct the settings.

 

 

 

The signal cables are not correctly connected.

10

 

Correctly connect the audio cables.

 

 

 

The MUTE function is working.

16

 

Restore the sound pressing MUTE or VOLUME button on

Sound does not

the remote control.

 

come out.

The volume is adjusted to an extremely low level.

16

 

Adjust the volume to a higher level using the menu function

 

or the remote control.

 

 

The AUDIO/SPEAKER setting is not correct.

35

 

Correctly set the AUDIO/SPEAKER in SETUP menu.

 

 

 

The lens cover is attached.

4, 15

No pictures are

Remove the lens cover.

 

displayed.

The signal cables are not correctly connected.

10

 

Correctly connect the connection cables.

 

 

(continued on next page)

58

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content Contents of package Fastening the lens coverProjector Part namesHOT Rear panel Control panelComponent Remote control Arrangement Setting upOn a horizontal surface Suspended from the ceiling Arrangement Setting up Speakers Connecting your devicesMonitor VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Using the security bar and slotAbout the remote control signal Remote controlPutting batteries Mouse right button Press Reset button Changing the frequency of remote control signalUsing as a simple PC mouse & keyboard Mouse left button Press Enter buttonTurning on the power Power on/offTurning off the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the sound For a computer signal Searching an input signalSelecting an input signal  For no signalAdjusting the projectors elevator Adjusting the zoom and focusAuto Using the automatic adjustment featureAdjusting the position PositionKeystone Using the magnify featureCorrecting the keystone distortions Magnify ON/OFFFreeze Freezing the screenTemporarily blanking the screen BlankUsing the menu function Easy MenuUsing the menu function Advanced MenuAuto Picture ModeAspect KeystoneEasy Menu Gamma Picture MenuColor Temp MY Memory Picture MenuLOAD-1, LOAD-2, LOAD-3, LOAD-4 SAVE-1, SAVE-2, SAVE-3, SAVE-4For adjusting Color Temp To adjust Custom function in Gamma and Color TempFor adjusting Gamma Gamma Color TempImage Menu For a computer signalFor no signal Over ScanImage Menu PhaseAuto Adjust SizeVideo NR Input MenuProgressive Color SpaceFrame Lock Input MenuVideo Format ComputerCustom ResolutionStandard Standard CustomSetup Menu Speaker Setup MenuVolume AudioScreen Menu BlankScreen Menu Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Sync is OUT of Range No Input is DetectedMessage Auto Search Option MenuAuto on Auto OFF Option MenuLamp Time MY Button ServiceFAN Speed Ghost Filter MessageRemote Freq Factory ResetKEY Lock InformationChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionIf you have forgotten your Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code Turning Off the PIN Lock Function Description SecurityIf you have forgotten your PIN Code Setting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Lamp MaintenanceType number Replacing the lamp Lamp warning LampAir filter Cleaning the air filterType number Page Internal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Resetting all settings Shutting the projector downSignal source does not correctly work Electrical power cord is not pluggedSignal cables are not correctly connected Input changeover settings are mismatchedNot properly adjusted Color settings are not correctly adjustedColor Space setting is not suitable Play monitorSpecification SpecificationsSpecification Specifications Intended Use
Related manuals
Manual 2 pages 52.39 Kb
Top Page Image Contents