3M X66 manual Specifications

Page 60

Specifications

Specifications

Specification

	Item		Specification

Product name			Liquid crystal projector
Liquid		Panel size	1.6 cm (0.63 type)
Crystal		Drive system	TFT active matrix
Panel		Pixels	786,432 pixels (1024 horizontal x 768 vertical)
Lens			Zoom lens,
Lens			F=1.6 ~ 1.8 f = 18.9~ 22.6 mm (approximately)
			F=1.6 ~ 1.8 f = 18.9~ 22.6 mm (approximately)
Lamp			220W UHB
Audio output			7 W
Power supply			AC 100-120V/3.5A, AC220-240V/1.5A
Power consumption			320W
Temperature range			5 ~ 35°C (Operating)
Size			340 (W) x 100 (H) x 270 (D) mm
Size			* Not including protruding parts. Please refer to the following figure.

Weight (mass)			approx. 3.5 kg
			Computer input port
			COMPUTER IN1	D-sub 15 pin mini x1
			COMPUTER IN2	D-sub 15 pin mini x1
			Computer output port
			MONITOR OUT	D-sub 15 pin mini x1
			Video input port
			Y, Cb/Pb, Cr/Pr (Component video)	RCA x3
			S-VIDEO	mini DIN 4 pin x1
Ports			VIDEO	RCA x1
			Audio input/output port
			AUDIO IN1	Stereo mini x1
			AUDIO IN2	Stereo mini x1
			AUDIO IN3	RCA x2
			AUDIO OUT	Stereo mini x1
			Others
			USB	USB-B x1
			CONTROL	D-sub 9 pin x1

60

Image 60

Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Contents of package Fastening the lens coverPart names ProjectorHOT Control panel Rear panelComponent Remote control Setting up ArrangementOn a horizontal surface Suspended from the ceiling Arrangement Setting up Connecting your devices MonitorSpeakers VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply Using the security bar and slotRemote control About the remote control signalPutting batteries Changing the frequency of remote control signal Using as a simple PC mouse & keyboardMouse right button Press Reset button Mouse left button Press Enter buttonPower on/off Turning on the powerTurning off the power Adjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Selecting an input signal For a computer signal  For no signalAdjusting the projectors elevator Adjusting the zoom and focusUsing the automatic adjustment feature Adjusting the positionAuto PositionUsing the magnify feature Correcting the keystone distortionsKeystone Magnify ON/OFFFreezing the screen Temporarily blanking the screenFreeze BlankUsing the menu function Easy MenuUsing the menu function Advanced MenuPicture Mode AspectAuto KeystoneEasy Menu Picture Menu GammaColor Temp Picture Menu LOAD-1, LOAD-2, LOAD-3, LOAD-4MY Memory SAVE-1, SAVE-2, SAVE-3, SAVE-4To adjust Custom function in Gamma and Color Temp For adjusting GammaFor adjusting Color Temp Gamma Color TempFor a computer signal For no signalImage Menu Over ScanPhase Auto AdjustImage Menu SizeInput Menu ProgressiveVideo NR Color SpaceInput Menu Video FormatFrame Lock ComputerResolution StandardCustom Standard CustomSetup Menu Setup Menu VolumeSpeaker AudioScreen Menu BlankScreen Menu Start UPCapturing error has occurred. Please try again MyScreenMyScreen registration is finished No Input is Detected Sync is OUT of RangeMessage Option Menu Auto SearchAuto on Option Menu Auto OFFLamp Time Service MY ButtonFAN Speed Ghost Filter MessageFactory Reset KEY LockRemote Freq InformationUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function If you have forgotten your PasswordTurning on the MyScreen Password Function Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code Description Security Turning Off the PIN Lock FunctionIf you have forgotten your PIN Code Using the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off Maintenance LampType number Replacing the lamp Lamp warning LampCleaning the air filter Air filterType number Page Troubleshooting There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Resetting all settings Shutting the projector downElectrical power cord is not plugged Signal cables are not correctly connectedSignal source does not correctly work Input changeover settings are mismatchedColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Play monitorSpecifications SpecificationSpecification Specifications Intended Use

Related manuals

Manual 2 pages 52.39 Kb