Onkyo SR804 Controlling Zone 2 with the Remote Controller, Adjusting the Volume for Zone

Zone 2—Continued

Controlling Zone 2 with the Remote Controller

STANDBY	ON	STANDBY
			TV
ON
			I	INPUT
	V1	V2	V3
	1	2	3	+
INPUT	V4	MULTI CH	DVD	TV CH
	4	5	6	-
SELECTOR	CD	TAPE	TUNER
	7	8	9
	PHONO			TV VOL
	+10	0	CLEAR
	- - / - - - 10	11	12
	INPUT SELECTOR
		MACRO

Adjusting the Volume for Zone 2

ZONE 2 LEVEL ,

MASTER VOLUME

STANDBY/ON

STANDBY

ZONE 2

POWER

ON

OFF

PURE AUDIO

MULTI CH

DVD

VIDEO 1

VIDEO 2

VIDEO 3

VIDEO 4

TAPE

TUNER

CD

PHONO

DISPLAY

PHONES

TUNING

ENTER

SETUP MIC

VIDEO 4 INPUT

ZONE 2

OFF

TONE

STEREO

DIMMER

MEMORY

MODE

SETUP

RETURN

LISTENING MODE

CLEAR

PRESET

PRESET

ZONE 2 LEVEL

TUNING

DIGITAL

S VIDEO

VIDEO

L AUDIO R

1	2	3	ZONE2	ZONE2
	REMOTE MODE
RECEIVER	DVD	CD	HDD
TAPE/AMP
	LISTENING MODE
STEREO	SURR
REPEAT	AUDIO	SUBTITLE PLAY MODE
PURE A	DIRECT	THX	ALLST
TEST TONE	CH SEL	LEVEL	LEVEL	LEVEL–,
OPEN/CLOSE VIDEO OFF
		L NIGHT	Re-EQ	LEVEL+
	RC-620M
Note:

1 ZONE2

LEVEL LEVEL

AV receiver

On the remote controller, press the [ZONE 2] REMOTE MODE but- ton, and then use the [LEVEL–] and [LEVEL+] buttons.

On the AV receiver, use the ZONE 2 LEVEL []/[ ] buttons.

•To control Zone 2, you must press the remote control- ler’s [ZONE 2] REMOTE MODE button first.

ZONE 2 LEVEL

1

ZONE2

ON

Press the [ZONE 2] REMOTE MODE button, then point the remote controller at the AV receiver and press the [ON] but- ton.

Zone 2 turns on, and the ZONE 2 12V TRIGGER OUT goes high (+12 V).

If your Zone 2 speakers are connected to an amp in Zone 2, use its volume control to adjust the volume.

To Mute Zone 2:

Press the remote controller’s [ZONE 2] button, followed by the [MUTING] button. To unmute Zone 2, press the remote controller’s [ZONE 2] button again, followed by the [MUTING] button, or adjust the volume for Zone 2.

Notes:

2

ZONE2

V1 V2 V3

1 2 3

V4DVD

46

CD TAPE TUNER

7 8 9

PHONO

+10

To select an input source for Zone 2, press the [ZONE 2] REMOTE MODE button, followed by an INPUT SELECTOR button.

To select AM, FM, or XM, press the [TUNER] INPUT SELECTOR button repeatedly.

•	Only analog input sources are output by the ZONE 2
	LINE OUT and ZONE 2 SPEAKERS terminals. Dig-
	ital input sources are not output. If no sound is heard
	when an input source is selected, check to see if it’s
	connected to an analog input.
•	When the ZONE 2 SPEAKERS terminals are used,
	listening modes that require surround back speakers,
	such as Dolby Digital EX, DTS-ES, and THX Select2
	Cinema, are unavailable.
•	While Zone 2 is on, the	functions do not work.
• You can’t select different radio stations for the main
	room and Zone 2. The same radio station will be used

3	To turn off Zone 2, press the
ZONE2	[ZONE 2] REMOTE MODE button,
	followed by the [STANDBY] but-
	ton.

STANDBY

for both.

84