LG Electronics System Setup Cont, Typical Setup Flow Chart for HCS6320, HDTV Service Feed

Page 14
System Setup (Cont.)

System Setup (Cont.)

Typical Setup Flow Chart for HCS6320

RF Cable

Typical Setup Flow Chart for HCS6320RF CableHDTV Service Feed RF In

HDTV Service Feed

Laptop

HD STB

(1 Per Program)

Out

In

HCS7720

 

 

 

 

CodePlus

Data Bus on

Transcoder Card

Card Frame

 

(1 Per Program)

Backplane

Service Port or Ethernet Connection

Card

HCS

 

 

Frame

6320

 

RF

(Up to 8

 

 

Cable

Inputs)

RF Out

 

 

 

 

 

 

 

PC

Combiner

RF

Distribution

System

14

206-4183

Page 13 Page 15
Image 14
Page 13 Page 15
Contents P/N 206-4183 Rev A HCS6320 CodePlus Series MUX/MOD Feature CardInstallation & Setup Guide Warranty Copyright 2012 LG Electronics U.S.A., IncREGULATORY INFORMATION For Customer Support/Service, please call­1-888-865-3026NOTE TO SATELLITE DISH INSTALLER COMPLIANCE6. Clean only with dry cloth IMPORTANT SAFETY INSTRUCTIONSImportant safeguards for you and your new product 7. Refer all servicing to qualified service personnel15. Safety Check Caution Refer all servicing to qualified service personnel14. Replacement Parts 13. ServicingTable of Contents Channel Assignments Setup InformationHCS6320 TranscodersFeatures HCS6320 Product DescriptionA typical Transcoder System with MUX/MOD functionality includes Transcoder Product DescriptionTypical HD Transcoder System Overview The integrated elements of the Transcoder SystemResets card HCS6320 Card DescriptionRESET Install after inserting HCS6320 cardHCS6320 Functional Blocks Installing a CodePlus Feature Card SERVICE Satellite STB & HCS6320 Initialization & Setup ConnectionsAC Power Cord Power Outlet 120V 60Hz AC Room Receiver Room Receiver Room ReceiverSystem Setup Typical HCS6320 System InstallationHDTV Service Feed System Setup ContTypical Setup Flow Chart for HCS6320 HD STBNetwork and Communication Setup Controller Menu Commands Configuration Options via GUIAccess the CodePlus Transcoder Series Web GUI Access the Controller MenuConfiguration Options via GUI Cont Read the RF Channel Map Display a List of Transcoder Cards Installed in the ChassisSet HCS6320 RF Channels Example List Cards DisplaySlot #7 Raw bitrate data 0 total Configure Card Number/Channel Assignments Example MUX Bitrates DisplaySet the HCS6320 IP Address Password changed Reset the Controller card to activate new IP settings. orReset the Controller card to activate new IP settings Change the Reload ProIdiom Key PasswordPerform an External Card Reset Success. Reset command sent to cardUpdate HCS6320 and/or Transcoder Firmware via TFTP Card Card HWID# is Transcoder Menu CommandsAccess the Transcoder Menu Example Transcoder MenuCard PI key checksum is Card OS version HCS7720-943-2011-1025 Encoder versionTotal Output Bitrate 19.390 Mbit/s View Software Information for a Selected TranscoderCard Reloading the key Successfully reloaded PI key Satellite STB Menu CommandsAccess the Satellite STB Menu Card 1 Tuner 1 Channel changed toExample Satellite STB Menu Card 1 Tuner Current STB Channel is Satellite signal is lockedSatellite signal strength is 52% Read the STB Channel and StatusCard 1 The STB is resetting Card 1 Tuner 1 STB Powered OnCard 1 Tuner 1 STB Powered Off Power the STB On or OffCard 1 Successfully cleared STB Update configuration Card 1 STB Update successfully configuredCard 1 STB Update is not scheduled. or Schedule an STB UpdateConfiguration Options via Command Line Access the HCS6320 Main MenuSet HCS6320 RF Channels Configuration Options via Command Line ContView HCS6320 System Information Print the RF Channels MapPerform an External Card Reset Display a List of Transcoder Cards Installed in the ChassisAccess Individual Transcoder Menus Enter IP address Type the host IP address in the format Install a ProIdiom Key on All TranscodersSet the HCS6320 IP Address Enter Subnet Mask Type the subnet mask in the formatTFTP Transfer 4. At the Use TFTP to download key y/n? prompt, eitherXmodem File Transfer Operation completed Update HCS6320 and/or Transcoder FirmwareReload the ProIdiom Key on All Transcoders 4. At the Enter card number 1-12, ‘ctr’, or ‘all’ prompt, eitherView MUX or Raw Bitrate Data Configure Card Number to Channel Assignments 1. RF 58-1 -- Slot #1 2. RF 58-2 -- Slot #2 3. RF 59-1 -- Slot #4 Reset Password for Reload PI Key GUI OptionSet Cross point switch... OK 4. RF 59-2 -- Slot #5 5. RF 60-1 -- Slot #8 6. RF 60-2 -- Slot #9Card #1 is HCS7720 HCS7720 1 Command Satellite Receiver MenuEncoder version Install a ProIdiom Key on the Selected TranscoderCard HWID# is HDMI Input Bitrate 6.684 Mbit/s raw 6.684 Mbit/sPI key checksum is 3. At the Use TFTP to transfer files y/n? prompt, eitherReload PI complete OK Reload the ProIdiom Key on the Selected TranscoderReset the Selected Transcoder Card Access the Satellite Receiver Menu for the Selected TranscoderUpdate Firmware on the Selected Transcoder Return to the HCS6320 Main MenuSatellite Receiver Menu Commands Access the Satellite Receiver MenuRead the Satellite Signal Strength Card 1 Satellite signal strength is 52%Card 1 Satellite signal is locked Card 1 Current STB channel isRead and/or Set STB Update Parameters At the Satellite # Command prompt, eitherPower the Satellite STB On or Off Card 1 STB serial# is R0128005665-792. At the Change STB Update setting y/n? prompt, either STB Update is not scheduledSTB Update is in progress Read STB Update ParametersSTB swver is X398RPLB-N Configured STB Update... OK Press any key to continueSTB model is ViP222k-HD Read the Satellite STB Model TypeSTATUS LED TroubleshootingEquipment Setup Review Audio/Video Freeze or Blank ScreenEnvironmental Storage Conditions SpecificationsDimensions Operating ConditionsDate Document Revision History / NotesDocument Revision History DescriptionOpen Source Software Notice Warranty begins on the date of delivery of the HCS6320 For Customer Support/Service, please call­LG HCS6320 MUX/MOD Feature Card Warranty Installation Guide
Top Page Image Contents