LG Electronics HCS6320 Slot #7 Raw bitrate data 0 total, Configuration Options via GUI Cont

Page 19
Slot #7 Raw bitrate data 0 total 0

Configuration Options via GUI (Cont.)

Example: List Card Details Display

card# card type

hardware id

os version

app

[enc]

1:[HCS7720] [7720-v1.1-2011-1026] [HCS7720-943-2011-1025] [2.5] [1.2]

2:[HCS7720] [7720-v1.1-2011-1026] [HCS7720-943-2011-1025] [2.5] [1.2]

3:[-]

4:[HCS7720] [7720-v1.1-2011-1026] [HCS7720-943-2011-1025] [2.5] [1.2]

5:[HCS7720] [7720-v1.1-2011-1026] [HCS7720-943-2011-1025] [2.5] [1.2]

6:[-]

7:[-]

8:[HCS7720] [7720-v1.1-2011-1026] [HCS7720-943-2011-1025] [2.5] [1.2]

9:[HCS7720] [7720-v1.1-2011-1026] [HCS7720-943-2011-1025] [2.5] [1.2]

10:[-]

11:[HCS7720] [7720-v1.1-2011-1026] [HCS7720-943-2011-1025] [2.5] [1.2]

12:[HCS7720] [7720-v1.1-2011-1026] [HCS7720-943-2011-1025] [2.5] [1.2]

View MUX or Raw Bitrate Data

Bitrate data is useful for system monitoring and troubleshooting purposes. Bitrates at the backplane (raw bitrates), are measured at the input pins prior to data processing. MUX bitrates provide information on MUX data processing, i.e., the amount of data filtering in and out of the MUX. See sample displays below and on the following page.

With the Controller Menu on display, either:

Click on the Read button at the right of the Read Bitrates at Backplane field to view raw bitrate data for each installed transcoder card.

Click on the Read button at the right of the Read MUX Bitrates field to view MUX bitrate data for each installed transcoder card.

Example: Bitrates at Backplane Connector (Raw Bitrates) Display

Slot #1 Raw bitrate data 14.228 Mbit/s total 19.396 Mbit/s Slot #2 Raw bitrate data 12.537 Mbit/s total 19.390 Mbit/s Slot #3 Raw bitrate data 0 total 0

Slot #4 Raw bitrate data 17.049 Mbit/s total 19.390 Mbit/s Slot #5 Raw bitrate data 15.503 Mbit/s total 19.396 Mbit/s Slot #6 Raw bitrate data 0 total 0

Slot #7 Raw bitrate data 0 total 0

Slot #8 Raw bitrate data 13.536 Mbit/s total 19.390 Mbit/s Slot #9 Raw bitrate data 13.957 Mbit/s total 19.396 Mbit/s Slot #10 Raw bitrate data 0 total 0

Slot #11 Raw bitrate data 7.520 Mbit/s total 19.396 Mbit/s Slot #12 Raw bitrate data 18.620 Mbit/s total 19.396 Mbit/s

Total number of data bits that are not null packets

Total number of data bits in the transport stream

206-4183

19

Image 19
Contents Copyright 2012 LG Electronics U.S.A., Inc HCS6320 CodePlus Series MUX/MOD Feature CardInstallation & Setup Guide Warranty P/N 206-4183 Rev ACOMPLIANCE For Customer Support/Service, please call­1-888-865-3026NOTE TO SATELLITE DISH INSTALLER REGULATORY INFORMATION7. Refer all servicing to qualified service personnel IMPORTANT SAFETY INSTRUCTIONSImportant safeguards for you and your new product 6. Clean only with dry cloth13. Servicing Caution Refer all servicing to qualified service personnel14. Replacement Parts 15. Safety CheckTable of Contents Transcoders Setup InformationHCS6320 Channel AssignmentsHCS6320 Product Description FeaturesThe integrated elements of the Transcoder System Transcoder Product DescriptionTypical HD Transcoder System Overview A typical Transcoder System with MUX/MOD functionality includesInstall after inserting HCS6320 card HCS6320 Card DescriptionRESET Resets cardHCS6320 Functional Blocks Installing a CodePlus Feature Card Room Receiver Room Receiver Room Receiver Satellite STB & HCS6320 Initialization & Setup ConnectionsAC Power Cord Power Outlet 120V 60Hz AC SERVICETypical HCS6320 System Installation System SetupHD STB System Setup ContTypical Setup Flow Chart for HCS6320 HDTV Service FeedNetwork and Communication Setup Access the Controller Menu Configuration Options via GUIAccess the CodePlus Transcoder Series Web GUI Controller Menu CommandsConfiguration Options via GUI Cont Example List Cards Display Display a List of Transcoder Cards Installed in the ChassisSet HCS6320 RF Channels Read the RF Channel MapSlot #7 Raw bitrate data 0 total Example MUX Bitrates Display Configure Card Number/Channel AssignmentsSet the HCS6320 IP Address Change the Reload ProIdiom Key Password Reset the Controller card to activate new IP settings. orReset the Controller card to activate new IP settings Password changedUpdate HCS6320 and/or Transcoder Firmware via TFTP Success. Reset command sent to cardPerform an External Card Reset Example Transcoder Menu Transcoder Menu CommandsAccess the Transcoder Menu Card Card HWID# isView Software Information for a Selected Transcoder Card OS version HCS7720-943-2011-1025 Encoder versionTotal Output Bitrate 19.390 Mbit/s Card PI key checksum isCard 1 Tuner 1 Channel changed to Satellite STB Menu CommandsAccess the Satellite STB Menu Card Reloading the key Successfully reloaded PI keyRead the STB Channel and Status Card 1 Tuner Current STB Channel is Satellite signal is lockedSatellite signal strength is 52% Example Satellite STB MenuPower the STB On or Off Card 1 Tuner 1 STB Powered OnCard 1 Tuner 1 STB Powered Off Card 1 The STB is resettingSchedule an STB Update Card 1 STB Update successfully configuredCard 1 STB Update is not scheduled. or Card 1 Successfully cleared STB Update configurationAccess the HCS6320 Main Menu Configuration Options via Command LinePrint the RF Channels Map Configuration Options via Command Line ContView HCS6320 System Information Set HCS6320 RF ChannelsAccess Individual Transcoder Menus Display a List of Transcoder Cards Installed in the ChassisPerform an External Card Reset Enter Subnet Mask Type the subnet mask in the format Install a ProIdiom Key on All TranscodersSet the HCS6320 IP Address Enter IP address Type the host IP address in the formatXmodem File Transfer 4. At the Use TFTP to download key y/n? prompt, eitherTFTP Transfer 4. At the Enter card number 1-12, ‘ctr’, or ‘all’ prompt, either Update HCS6320 and/or Transcoder FirmwareReload the ProIdiom Key on All Transcoders Operation completedView MUX or Raw Bitrate Data Configure Card Number to Channel Assignments 4. RF 59-2 -- Slot #5 5. RF 60-1 -- Slot #8 6. RF 60-2 -- Slot #9 Reset Password for Reload PI Key GUI OptionSet Cross point switch... OK 1. RF 58-1 -- Slot #1 2. RF 58-2 -- Slot #2 3. RF 59-1 -- Slot #4Satellite Receiver Menu Card #1 is HCS7720 HCS7720 1 CommandHDMI Input Bitrate 6.684 Mbit/s raw 6.684 Mbit/s Install a ProIdiom Key on the Selected TranscoderCard HWID# is Encoder versionReload the ProIdiom Key on the Selected Transcoder 3. At the Use TFTP to transfer files y/n? prompt, eitherReload PI complete OK PI key checksum isReturn to the HCS6320 Main Menu Access the Satellite Receiver Menu for the Selected TranscoderUpdate Firmware on the Selected Transcoder Reset the Selected Transcoder CardAccess the Satellite Receiver Menu Satellite Receiver Menu CommandsCard 1 Current STB channel is Card 1 Satellite signal strength is 52%Card 1 Satellite signal is locked Read the Satellite Signal StrengthCard 1 STB serial# is R0128005665-79 At the Satellite # Command prompt, eitherPower the Satellite STB On or Off Read and/or Set STB Update ParametersRead STB Update Parameters STB Update is not scheduledSTB Update is in progress 2. At the Change STB Update setting y/n? prompt, eitherRead the Satellite STB Model Type Configured STB Update... OK Press any key to continueSTB model is ViP222k-HD STB swver is X398RPLB-NAudio/Video Freeze or Blank Screen TroubleshootingEquipment Setup Review STATUS LEDOperating Conditions SpecificationsDimensions Environmental Storage ConditionsDescription Document Revision History / NotesDocument Revision History DateOpen Source Software Notice Installation Guide For Customer Support/Service, please call­LG HCS6320 MUX/MOD Feature Card Warranty Warranty begins on the date of delivery of the HCS6320