LG Electronics HCS6320 setup guide Satellite STB Menu Commands, Card 1 Tuner 1 Channel changed to

Page 26
Reload the Pro:Idiom Key on a Selected Transcoder

Configuration Options via GUI (Cont.)

Reload the Pro:Idiom Key on a Selected Transcoder

This command reloads the Pro:Idiom encryption key on a single transcoder card. Note that a password is required to initiate this command.

1.With the Transcoder Menu on display, click on the down arrow at the right of the Card Select field, and select the appropriate transcoder card from the drop-down list of options.

2.Click on the Reload button at the right of the Reload PI Key field.

3.At the pop-up window prompt for the password required to execute the operation, type the password and click OK.

When the reload is complete, the system will display confirmation, for example:

Card 1:

Reloading the key ...

Successfully reloaded PI key

Satellite STB Menu Commands

The following subsections describe how to access and use the Satellite STB Menu commands.

Access the Satellite STB Menu

1.Access the CodePlus Transcoder Series web GUI as described on page 16.

2.With the Homepage on display, click on the Satellite STB menu tab or link.

The Satellite STB Menu (see example on following page) enables you to view and modify selected satellite STB configuration settings.

Note: The Tuner Select field in the Satellite STB Menu is irrelevant and should be left at its default value (Tuner “1”) when HCS7720 transcoder cards are being used. Results displays that include tuner data for an HCS7720/ViP 222k STB pair will always specify Tuner 1.

Set the STB Channel

1.With the Satellite STB Menu on display, click on the down arrow at the right of the Card Select field, and select the appropriate card from the drop-down list of options.

2.Type the desired channel number (1 – 9999) in the Set Tuner Channel field, and then click on the Set button at the right of the entry field.

If the channel is set successfully, the satellite STB will change to the specified DISH Network channel and the system will display confirmation, for example:

Card 1 Tuner 1: Channel changed to 209

26

206-4183

Image 26
Contents P/N 206-4183 Rev A HCS6320 CodePlus Series MUX/MOD Feature CardInstallation & Setup Guide Warranty Copyright 2012 LG Electronics U.S.A., IncREGULATORY INFORMATION For Customer Support/Service, please call­1-888-865-3026NOTE TO SATELLITE DISH INSTALLER COMPLIANCE6. Clean only with dry cloth IMPORTANT SAFETY INSTRUCTIONSImportant safeguards for you and your new product 7. Refer all servicing to qualified service personnel15. Safety Check Caution Refer all servicing to qualified service personnel14. Replacement Parts 13. ServicingTable of Contents Channel Assignments Setup InformationHCS6320 TranscodersFeatures HCS6320 Product DescriptionA typical Transcoder System with MUX/MOD functionality includes Transcoder Product DescriptionTypical HD Transcoder System Overview The integrated elements of the Transcoder SystemResets card HCS6320 Card DescriptionRESET Install after inserting HCS6320 cardHCS6320 Functional Blocks Installing a CodePlus Feature Card SERVICE Satellite STB & HCS6320 Initialization & Setup ConnectionsAC Power Cord Power Outlet 120V 60Hz AC Room Receiver Room Receiver Room ReceiverSystem Setup Typical HCS6320 System InstallationHDTV Service Feed System Setup ContTypical Setup Flow Chart for HCS6320 HD STBNetwork and Communication Setup Controller Menu Commands Configuration Options via GUIAccess the CodePlus Transcoder Series Web GUI Access the Controller MenuConfiguration Options via GUI Cont Read the RF Channel Map Display a List of Transcoder Cards Installed in the ChassisSet HCS6320 RF Channels Example List Cards DisplaySlot #7 Raw bitrate data 0 total Configure Card Number/Channel Assignments Example MUX Bitrates DisplaySet the HCS6320 IP Address Password changed Reset the Controller card to activate new IP settings. orReset the Controller card to activate new IP settings Change the Reload ProIdiom Key PasswordPerform an External Card Reset Success. Reset command sent to cardUpdate HCS6320 and/or Transcoder Firmware via TFTP Card Card HWID# is Transcoder Menu CommandsAccess the Transcoder Menu Example Transcoder MenuCard PI key checksum is Card OS version HCS7720-943-2011-1025 Encoder versionTotal Output Bitrate 19.390 Mbit/s View Software Information for a Selected TranscoderCard Reloading the key Successfully reloaded PI key Satellite STB Menu CommandsAccess the Satellite STB Menu Card 1 Tuner 1 Channel changed toExample Satellite STB Menu Card 1 Tuner Current STB Channel is Satellite signal is lockedSatellite signal strength is 52% Read the STB Channel and StatusCard 1 The STB is resetting Card 1 Tuner 1 STB Powered OnCard 1 Tuner 1 STB Powered Off Power the STB On or OffCard 1 Successfully cleared STB Update configuration Card 1 STB Update successfully configuredCard 1 STB Update is not scheduled. or Schedule an STB UpdateConfiguration Options via Command Line Access the HCS6320 Main MenuSet HCS6320 RF Channels Configuration Options via Command Line ContView HCS6320 System Information Print the RF Channels MapPerform an External Card Reset Display a List of Transcoder Cards Installed in the ChassisAccess Individual Transcoder Menus Enter IP address Type the host IP address in the format Install a ProIdiom Key on All TranscodersSet the HCS6320 IP Address Enter Subnet Mask Type the subnet mask in the formatTFTP Transfer 4. At the Use TFTP to download key y/n? prompt, eitherXmodem File Transfer Operation completed Update HCS6320 and/or Transcoder FirmwareReload the ProIdiom Key on All Transcoders 4. At the Enter card number 1-12, ‘ctr’, or ‘all’ prompt, eitherView MUX or Raw Bitrate Data Configure Card Number to Channel Assignments 1. RF 58-1 -- Slot #1 2. RF 58-2 -- Slot #2 3. RF 59-1 -- Slot #4 Reset Password for Reload PI Key GUI OptionSet Cross point switch... OK 4. RF 59-2 -- Slot #5 5. RF 60-1 -- Slot #8 6. RF 60-2 -- Slot #9Card #1 is HCS7720 HCS7720 1 Command Satellite Receiver MenuEncoder version Install a ProIdiom Key on the Selected TranscoderCard HWID# is HDMI Input Bitrate 6.684 Mbit/s raw 6.684 Mbit/sPI key checksum is 3. At the Use TFTP to transfer files y/n? prompt, eitherReload PI complete OK Reload the ProIdiom Key on the Selected TranscoderReset the Selected Transcoder Card Access the Satellite Receiver Menu for the Selected TranscoderUpdate Firmware on the Selected Transcoder Return to the HCS6320 Main MenuSatellite Receiver Menu Commands Access the Satellite Receiver MenuRead the Satellite Signal Strength Card 1 Satellite signal strength is 52%Card 1 Satellite signal is locked Card 1 Current STB channel isRead and/or Set STB Update Parameters At the Satellite # Command prompt, eitherPower the Satellite STB On or Off Card 1 STB serial# is R0128005665-792. At the Change STB Update setting y/n? prompt, either STB Update is not scheduledSTB Update is in progress Read STB Update ParametersSTB swver is X398RPLB-N Configured STB Update... OK Press any key to continueSTB model is ViP222k-HD Read the Satellite STB Model TypeSTATUS LED TroubleshootingEquipment Setup Review Audio/Video Freeze or Blank ScreenEnvironmental Storage Conditions SpecificationsDimensions Operating ConditionsDate Document Revision History / NotesDocument Revision History DescriptionOpen Source Software Notice Warranty begins on the date of delivery of the HCS6320 For Customer Support/Service, please call­LG HCS6320 MUX/MOD Feature Card Warranty Installation Guide