Mitsubishi Electronics XL21, XL50 installation manual External AC fan attaching occasional

Page 17
Intake vent
External AC fan

External AC fan attaching (occasional)

When 4-high configuration with 50” Single, attach the optional external AC fans (JC-AF115R or JC-AF230R) on intake vents. Even in 3-high configuration, attach the AC fans as well, when spaces are narrower than 50cm to the ceiling and 10cm to the wall behind. Narrow spaces tend to rise the cube internal heat. Be sure this work is only for the cubes in the bottom row.

1.Attach a suitable plug to the bare end of the power cord of the fan to correspond with an interface such as a terminal block or a power strip. 2-meter AC power cord is included in the fan.

2.Insert the fan into the intake vent till click.

3.Fix it to the lower part of cube with the screw supplied

with the fan. Note:

To avoid injuries and shock hazards, do not carry electricity to the fan during this work. It must be done by qualified personnel.

Be sure to use the fan within the range of its power rating.

The outline of the fan is shown below. Prepare a base stand which does not interfere with the fan.

Lower part of cube

External

AC fan

[Unit: mm]

Front view

Side view

REV 2.4

17

Image 17
Contents Set-up and Installation Manual Table of Contents REV 118 Product lineup Set-up and installation OverviewFlowchart Preparation Cube installationSafety precaution Input board installation optional Color wheel unlocking Unlocking for XL21Lamp cushion removing for Changer PH50 Cube stacking for Rear Assembling the base stands and cubesScreen gap adjustment Fixing to the wall and floor Tape peeling off for Cube stacking for FrontScreen detaching For 67 , 50 Changer VentilationFor 50 Single External AC fan attaching occasional Assembling base stands and cubes As needed, you can adjust the screen gaps Adjustment Screen opening Screen open/close for FrontScreen closing Control signal connection ConnectingImage signal connection Case of daisy chainInternal cabling for Front For other than daisy chainMenu operation Control button list Initial set upOperation mode Remote ID Basic menu operationDisplaying internal test pattern Dipswitch settingPicture outline adjustment Attaching Axis adjustmentFront Close the screen .2.7.2, on Detaching AdjustmentPosition Keystone Tilt Zoom Correct the horizontal keystone distortion Mirror adjustment 50 XL21 XL50 Rear and PH50 System set up Lamp Power System memory settingLamp Mode for XL21 This adjustment is normally unnecessary Terminate This adjustment is normally unnecessaryOverlap for the input board Start MemorySystem Sync Image Flip This adjustment is normally unnecessaryBaud Rate Indication This adjustment is normally unnecessary Extended ID Auto Power onCable Length for PH50 and XL50 Resolution for PH50 This adjustment is normally unnecessaryDirection This adjustment is normally unnecessary Changer Lamp Change forBlack Level This adjustment is not necessary Color balance adjustmentREV Gradation White BalanceSensor Target ColorColor Matrixuser Image set upADV.DARK This adjustment is normally unnecessary ADV.COL This adjustment is normally unnecessaryGamma This adjustment is normally unnecessary Dither This adjustment is normally unnecessaryWhite Boost This adjustment is normally unnecessary Input port selecting Input memory setting for the main inputAutomatic input signal scanning 3.1. H.POSITION, V.POSITION Signal adjustmentFine for Analog input AMP Gain for Analog inputSignal Select Signal Select for XL21Clamp START=0, Clamp WIDTH=0. Procedure Brightness ContrastColor Matrix ApertureInput memory calling/deleting Input memory savingExpansion setting Input memory setting for the input boardFine for S.ANALOG input 4.1. H.POSITION, V.POSITIONAMP. Gain for S.ANALOG input Scanning Value is automatically set in automatic input signalClamp START=0, Clamp WIDTH=0. Procedure With VC-B20KA Brightness ASPECT-RATIO VCR Mode for Composite or Y/C input with VC-B20KVColor for Composite or Y/C input Tint for Composite or Y/C inputInput memory saving 2. H.DISPLAY POS, V.DISPLAY POS Display memory setting for the input boardInput Memory Digital OUT Screen ModeDisplay memory calling/deleting Display memory savingSetting as daisy chain connection for the input board Display POS /1 Safety precautions Regular maintenance 2.1. Lamp replacementFor Single ProcedureTighten the two lamp fixing screws For Changer Open the lamp cover Close the lamp cover Partition door Action in brightness deterioration Auto-lamp changing function for ChangerAction in lamp failure burnout or explosion Lamp position auto calibration Manual lamp swapLamp will Exchange Soon Condenser lens adjustment for Single Focus adjustment Cleaning procedure CleaningScreen front surface CabinetFilter Time Filter ResetFor delivery Axis adjuster fixingColor wheel locking for XL21 Lamp cushion inserting forScreen-holding arm locking for 67 Front FrontMenu trees Function MemoriesInput memory Common itemsDisplay memory Additional items When Analog or S.ANALOG is selectedAdditional items When S.DIGITAL is selected Items within parentheses are initial values System memoryMemory list display LED display Test pattern listControl panel LED display list Control terminal Terminal functionsRS-232C terminal Available input signal list RGB signal Ycbcr Ypbpr component video signal Accessory Motorized adjustment tool, S-AXL50E specificationApplicable product Outline drawingRotary dial Terminal for firmware upgrading/slide switchTerminals Outline Recovery procedure from error Reset buttonTrouble shooting LEDInitial set-up Adjustment software, Wallaby 4.1. GeneralInstallation Automatic panel ID setting System configuration settingManual panel ID setting Serial port settingSerial port opening AdjustmentTurning on Picture mute offMaintenance Service tab for system memoryOptimize gain function Auto CSC functionInstallation Misc Function Input tab for input memory 107 Additional items When Composite or Y/C is selected Display tab for display memory Information tab Memory tabMemory copy Data sending to cubes Memory backupCube data saving Main window Power and MutePanel selection area Serial PortMenu bar Send Parameter Edit menu Read ParameterCopy Parameter Paste ParameterOther Wall Config… System Config menu By n 1x1, 2x2, 3x3 orCube ID Setting Auto IDSpecial menu Protect Setting Port SettingSerial Port menu Log… OpenAbout trademarks Description Revision date Revision history

XL21, XL50 specifications

Mitsubishi Electronics has consistently set benchmarks in the realm of display technologies, and their XL50 and XL21 projector series showcases this commitment to excellence. These models are meticulously designed to cater to a variety of professional environments, making them indispensable tools for businesses, education, and large venues.

The flagship XL50 projectors offer superior brightness with an impressive maximum output, ensuring vivid images even in well-lit rooms. With a native resolution that supports Full HD content, users can expect crystal-clear presentations that captivate audiences. The XL50 also incorporates advanced color reproduction technologies, which provide a wide color gamut for dynamic visual experiences. The projectors utilize Mitsubishi’s proprietary 3LCD technology, which enhances color accuracy and brightness, allowing for incredible detail and realism in every projected image.

In contrast, the XL21 models are tailored for users seeking a balance between affordability and performance. While slightly less powerful than the XL50, these projectors still deliver remarkable brightness, making them suitable for small to medium-sized meeting rooms and classrooms. The XL21 also features a compact and lightweight design, facilitating easy transportation and setup. With a focus on user-friendly operation, both models offer intuitive interfaces and connectivity options, including HDMI ports, VGA connections, and wireless capabilities, enabling seamless integration with other devices.

In terms of advanced features, both the XL50 and XL21 incorporate automatic keystone correction and digital zoom capabilities, ensuring that images are always perfectly aligned regardless of projector placement. They also come equipped with robust security features, which are essential in corporate environments. This includes password protection and a security bar, adding an extra layer of protection against unauthorized access.

In conclusion, the Mitsubishi Electronics XL50 and XL21 projectors stand out for their exceptional brightness, advanced color technologies, and user-friendly features. They are designed to meet the diverse needs of various professional settings, whether delivering impactful presentations in large auditoriums or facilitating engaging learning experiences in classrooms. As a result, these projectors exemplify Mitsubishi Electronics’ dedication to innovation and quality in the display technology industry.