Mitsubishi Electronics XL21, XL50 installation manual Axis adjustment, Attaching

Page 29

Slide switch

OPE RESET FACTORY

1.4.3.2.6-axis adjustment

1.4.3.2.1.Release the lock screws Before 6-axis adjustment, release locks in the adjuster. Loosen 4 locking screws with an Allen wrench (2mm) and 5 fixing screws with an Allen wrench (4mm).

4 locking screws

5 fixing screws

1.4.3.2.2.When adjusting with motorized adjustment tool, S-AXL50E

Attaching

1.Set the rotary dial in the upper unit of the adjustment tool according to

the product (chapter 3.8.4.2, on page 97). The initial setting is 0.

•Front: Set it 0.

•Rear: Set it 1.

2.Make sure the slide switch is set OPE (right side).

3.Connect the upper and lower units with a supplied unit-connecting cable.

4.Connect a supplied cube-connecting cable with upper unit.

5.Open the screen (chapter 1.2.7.1, on page 21) or rear panel to access the 6-axis adjuster.

Note:

For Rear, open the rear panel 180 degrees or remove it to perform the adjustment. Adjustment with half-open panel may cause breakage due to interference with the adjustment tool.

Rotary Dial

POWER 0:FRONT ERROR FW-EN 1:REAR

9:TEST

Upper unit

Lower unit

Cube-connecting cable Unit-connecting cable

Rear panel

REV 2.4

29

Image 29

Contents

Set-up and Installation Manual Table of Contents REV 118 Product lineup Set-up and installation OverviewFlowchart Preparation Cube installationSafety precaution Input board installation optional Color wheel unlocking Unlocking for XL21Lamp cushion removing for Changer PH50 Cube stacking for Rear Assembling the base stands and cubesScreen gap adjustment Fixing to the wall and floor Tape peeling off for Cube stacking for FrontScreen detaching For 67 , 50 Changer VentilationFor 50 Single External AC fan attaching occasional Assembling base stands and cubes As needed, you can adjust the screen gaps Adjustment Screen opening Screen open/close for FrontScreen closing Control signal connection ConnectingImage signal connection Case of daisy chainInternal cabling for Front For other than daisy chain Menu operation Control button list Initial set upOperation mode Remote ID Basic menu operationDisplaying internal test pattern Dipswitch settingPicture outline adjustment Attaching Axis adjustmentFront Close the screen .2.7.2, on Detaching AdjustmentPosition Keystone Tilt Zoom Correct the horizontal keystone distortion Mirror adjustment 50 XL21 XL50 Rear and PH50 System set up Lamp Power System memory settingLamp Mode for XL21 This adjustment is normally unnecessary Terminate This adjustment is normally unnecessaryOverlap for the input board Start MemorySystem Sync Image Flip This adjustment is normally unnecessaryBaud Rate Indication This adjustment is normally unnecessary Extended ID Auto Power onCable Length for PH50 and XL50 Resolution for PH50 This adjustment is normally unnecessaryDirection This adjustment is normally unnecessary Changer Lamp Change forBlack Level This adjustment is not necessary Color balance adjustmentREV Gradation White BalanceSensor Target ColorColor Matrixuser Image set upADV.DARK This adjustment is normally unnecessary ADV.COL This adjustment is normally unnecessaryGamma This adjustment is normally unnecessary Dither This adjustment is normally unnecessaryWhite Boost This adjustment is normally unnecessary Input port selecting Input memory setting for the main inputAutomatic input signal scanning 3.1. H.POSITION, V.POSITION Signal adjustmentFine for Analog input AMP Gain for Analog inputSignal Select Signal Select for XL21Clamp START=0, Clamp WIDTH=0. Procedure Brightness ContrastColor Matrix ApertureInput memory calling/deleting Input memory savingExpansion setting Input memory setting for the input boardFine for S.ANALOG input 4.1. H.POSITION, V.POSITIONAMP. Gain for S.ANALOG input Scanning Value is automatically set in automatic input signalClamp START=0, Clamp WIDTH=0. Procedure With VC-B20KA Brightness ASPECT-RATIO VCR Mode for Composite or Y/C input with VC-B20KVColor for Composite or Y/C input Tint for Composite or Y/C inputInput memory saving 2. H.DISPLAY POS, V.DISPLAY POS Display memory setting for the input boardInput Memory Digital OUT Screen ModeDisplay memory calling/deleting Display memory savingSetting as daisy chain connection for the input board Display POS /1 Safety precautions Regular maintenance 2.1. Lamp replacementFor Single ProcedureTighten the two lamp fixing screws For Changer Open the lamp cover Close the lamp cover Partition door Action in brightness deterioration Auto-lamp changing function for ChangerAction in lamp failure burnout or explosion Lamp position auto calibration Manual lamp swapLamp will Exchange Soon Condenser lens adjustment for Single Focus adjustment Cleaning procedure CleaningScreen front surface CabinetFilter Time Filter ResetFor delivery Axis adjuster fixingColor wheel locking for XL21 Lamp cushion inserting forScreen-holding arm locking for 67 Front FrontMenu trees Function MemoriesInput memory Common itemsDisplay memory Additional items When Analog or S.ANALOG is selectedAdditional items When S.DIGITAL is selected Items within parentheses are initial values System memoryMemory list display LED display Test pattern listControl panel LED display list Control terminal Terminal functionsRS-232C terminal Available input signal list RGB signal Ycbcr Ypbpr component video signal Accessory Motorized adjustment tool, S-AXL50E specificationApplicable product Outline drawingRotary dial Terminal for firmware upgrading/slide switchTerminals Outline Recovery procedure from error Reset buttonTrouble shooting LEDInitial set-up Adjustment software, Wallaby 4.1. GeneralInstallation Automatic panel ID setting System configuration settingManual panel ID setting Serial port settingSerial port opening AdjustmentTurning on Picture mute offMaintenance Service tab for system memoryOptimize gain function Auto CSC functionInstallation Misc Function Input tab for input memory 107 Additional items When Composite or Y/C is selected Display tab for display memory Information tab Memory tabMemory copy Data sending to cubes Memory backupCube data saving Main window Power and MutePanel selection area Serial PortMenu bar Send Parameter Edit menu Read ParameterCopy Parameter Paste ParameterOther Wall Config… System Config menu By n 1x1, 2x2, 3x3 orCube ID Setting Auto IDSpecial menu Protect Setting Port SettingSerial Port menu Log… OpenAbout trademarks Description Revision date Revision history